Question 260
Two workloads reside in the same IP subnet but policy requires stricter isolation for only a tagged set of VMs. A follow-up access review asks the team to validate the same boundary with a controlled negative test. What information should be inspected before the change is applied?
- Inspect DAI drop counters, DHCP snooping binding table, static host assignments and ARP inspection logs.
- Inspect VM attributes, uSeg EPG selectors, endpoint placement and resulting enforced contracts.
- Inspect source guard state, DHCP snooping bindings, static exceptions and ingress drop reasons.
- Inspect EPG bindings, contracts, subject filters, provider-consumer association and zoning rules.
Explanation
Correct Answer
B:Inspect VM attributes, uSeg EPG selectors, endpoint placement and resulting enforced contracts. These records help distinguish the suspected failure from a superficially similar fault before modifying production. Microsegmentation can classify subsets of endpoints beyond broad subnet grouping and apply finer-grained controls. A follow-up access review asks the team to validate the same boundary with a controlled negative test.
Incorrect Answers
A:Inspect DAI drop counters, DHCP snooping binding table, static host assignments and ARP inspection logs. This concerns dynamic ARP inspection source of truth, not aci microsegmentation selector.
C:Inspect source guard state, DHCP snooping bindings, static exceptions and ingress drop reasons. This concerns first-hop ip/mac spoof defense, not aci microsegmentation selector.
D:Inspect EPG bindings, contracts, subject filters, provider-consumer association and zoning rules. This concerns aci inter-epg contract, not aci microsegmentation selector.
Question 261
Layer 2 VXLAN segments work but traffic between tenant IP subnets fails because the L3 VNI is associated with the wrong VRF. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence. What post-change observation gives the strongest evidence of success?
- Inter-subnet routes are installed in the correct VRF and authorized host traffic routes between VNIs.
- The collector receives fresh, structured device state and alerts on a deliberately induced test event.
- ARP broadcasts reach all intended member VTEPs without loops or unintended tenant leakage.
- Hosts retain default-gateway reachability through a controlled active-router failure test.
Explanation
Correct Answer
A:Inter-subnet routes are installed in the correct VRF and authorized host traffic routes between VNIs. This result tests the original failure rather than reporting merely that the configuration command was accepted. Integrated routing and bridging requires consistent L3 VNI and tenant routing context for inter-subnet forwarding. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence.
Incorrect Answers
B:The collector receives fresh, structured device state and alerts on a deliberately induced test event. This concerns streaming telemetry health, not evpn vni-to-vrf mapping.
C:ARP broadcasts reach all intended member VTEPs without loops or unintended tenant leakage. This concerns bum replication behavior, not evpn vni-to-vrf mapping.
D:Hosts retain default-gateway reachability through a controlled active-router failure test. This concerns first-hop gateway failover, not evpn vni-to-vrf mapping.
Question 262
Two workloads reside in the same IP subnet but policy requires stricter isolation for only a tagged set of VMs. A follow-up access review asks the team to validate the same boundary with a controlled negative test. What is the best next implementation or troubleshooting step?
- Validate DAI binding sources and configure a supported static ARP ACL or binding for the approved fixed-address hosts.
- Use supported ACI microsegmentation classification and policy to distinguish the tagged workloads.
- Apply and validate a narrowly scoped ACI contract with the required provider-consumer relationship and filters.
- Assign a restricted read-only RBAC role covering the required monitoring commands.
Explanation
Correct Answer
B:Use supported ACI microsegmentation classification and policy to distinguish the tagged workloads. Microsegmentation can classify subsets of endpoints beyond broad subnet grouping and apply finer-grained controls. A follow-up access review asks the team to validate the same boundary with a controlled negative test.
Incorrect Answers
A:Validate DAI binding sources and configure a supported static ARP ACL or binding for the approved fixed-address hosts. This concerns dynamic ARP inspection source of truth, not aci microsegmentation selector.
C:Apply and validate a narrowly scoped ACI contract with the required provider-consumer relationship and filters. This concerns aci inter-epg contract, not aci microsegmentation selector.
D:Assign a restricted read-only RBAC role covering the required monitoring commands. This concerns nx-os administrative RBAC, not aci microsegmentation selector.
Question 263
A server sees intermittent TCP resets, but an administrator only has coarse interface error counters. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence. Which evidence set most directly tests the suspected failure?
- Inspect SPAN source/destination selection, capture timestamps, TCP flags and any truncation or drop counters.
- Inspect neighbor state, interface area assignments, hello parameters and interface MTU on both peers.
- Inspect affected path topology, fabric insights, health anomalies and matching device performance timelines.
- Inspect peer-link state, peer-keepalive reachability, consistency checks and suspended port reasons.
Explanation
Correct Answer
A:Inspect SPAN source/destination selection, capture timestamps, TCP flags and any truncation or drop counters. These records help distinguish the suspected failure from a superficially similar fault before modifying production. SPAN copies selected frames for packet inspection when protocol-level behavior is not visible in summarized counters. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence.
Incorrect Answers
B:Inspect neighbor state, interface area assignments, hello parameters and interface MTU on both peers. This concerns OSPF area compatibility, not span packet-level diagnosis.
C:Inspect affected path topology, fabric insights, health anomalies and matching device performance timelines. This concerns nexus dashboard fabric visibility, not span packet-level diagnosis.
D:Inspect peer-link state, peer-keepalive reachability, consistency checks and suspended port reasons. This concerns vpc peer-link recovery, not span packet-level diagnosis.
Question 264
A fabric dashboard displays healthy switch reachability but a service experiences consistent high-latency paths. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence. Which intervention most directly addresses the stated condition?
- Correlate Nexus Dashboard health and topology insights with time-specific switch and traffic telemetry.
- Align EVPN route-target import policy and local tenant VRF configuration for the relevant VNI.
- Enable a supported streaming telemetry subscription and validate the model paths and collector delivery.
- Confirm the designated root and spanning-tree role before changing a port that is intentionally blocking a loop.
Explanation
Correct Answer
A:Correlate Nexus Dashboard health and topology insights with time-specific switch and traffic telemetry. Fabric assurance tools combine topology and operational observations but require data correlation to identify service causes. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence.
Incorrect Answers
B:Align EVPN route-target import policy and local tenant VRF configuration for the relevant VNI. This concerns mp-BGP tenant route import, not nexus dashboard fabric visibility.
C:Enable a supported streaming telemetry subscription and validate the model paths and collector delivery. This concerns streaming telemetry health, not nexus dashboard fabric visibility.
D:Confirm the designated root and spanning-tree role before changing a port that is intentionally blocking a loop. This concerns rstp blocked uplink, not nexus dashboard fabric visibility.
Question 265
A new Fibre Channel host is connected to an MDS switch but never receives a fabric identifier and cannot discover targets. A storage change board requires a traceable diagnosis before allowing further fabric changes. Which intervention most directly addresses the stated condition?
- Validate physical FC link and initiator FLOGI registration before changing storage-array masking.
- Investigate Fibre Channel domain ID assignments and fabric merge requirements before allowing the ISL to join.
- Apply a least-privilege zoning design with an individual initiator and explicitly approved target members per zone.
- Align interface speed, VSAN mode and compatibility parameters across the intended port-channel members.
Explanation
Correct Answer
A:Validate physical FC link and initiator FLOGI registration before changing storage-array masking. An initiator must complete fabric login and receive an FCID before normal fabric services can identify it. A storage change board requires a traceable diagnosis before allowing further fabric changes.
Incorrect Answers
B:Investigate Fibre Channel domain ID assignments and fabric merge requirements before allowing the ISL to join. That response is associated with fcid and domain id stability rather than the specific fibre channel fabric login condition described here. For the stated failure, the preferred action is: Validate physical FC link and initiator FLOGI registration before changing storage-array masking. Relevant evidence: Inspect FC interface state, FLOGI database, initiator WWPN and relevant switch events. A storage change board requires a traceable diagnosis before allowing further fabric changes.
C:Apply a least-privilege zoning design with an individual initiator and explicitly approved target members per zone. This concerns single-initiator zoning, not fibre channel fabric login.
D:Align interface speed, VSAN mode and compatibility parameters across the intended port-channel members. That response is associated with fibre channel port-channel consistency rather than the specific fibre channel fabric login condition described here. For the stated failure, the preferred action is: Validate physical FC link and initiator FLOGI registration before changing storage-array masking. Relevant evidence: Inspect FC interface state, FLOGI database, initiator WWPN and relevant switch events. A storage change board requires a traceable diagnosis before allowing further fabric changes.
Question 266
During an east-west bandwidth surge, interface counters rise but do not reveal which applications or source subnets dominate. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence. Which test result best demonstrates restoration of the intended behavior?
- Remote MAC/IP routes appear in the EVPN database and tested inter-VTEP traffic succeeds.
- Hosts retain default-gateway reachability through a controlled active-router failure test.
- Receivers begin receiving the intended group traffic and multicast routing entries show the expected incoming interface.
- Traffic flows identify the actual high-volume conversations and support a targeted capacity or policy fix.
Explanation
Correct Answer
D:Traffic flows identify the actual high-volume conversations and support a targeted capacity or policy fix. This result tests the original failure rather than reporting merely that the configuration command was accepted. Flow records expose traffic conversations and volume patterns that interface-level totals cannot distinguish. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence.
Incorrect Answers
A:Remote MAC/IP routes appear in the EVPN database and tested inter-VTEP traffic succeeds. This concerns mp-BGP evpn route learning, not netflow traffic attribution.
B:Hosts retain default-gateway reachability through a controlled active-router failure test. This concerns first-hop gateway failover, not netflow traffic attribution.
C:Receivers begin receiving the intended group traffic and multicast routing entries show the expected incoming interface. This concerns PIM multicast rendezvous point, not netflow traffic attribution.
Question 267
A four-link server port-channel forwards on two members because the other members use incompatible trunk settings. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence. Which result would best confirm that the remediation worked?
- The intended root remains stable, the active forwarding path operates and the redundant link converges after a fault.
- The pair reaches Full state and the intended prefixes appear in the OSPF route table without new adjacency flaps.
- Peer-link adjacency and vPC consistency return healthy, and affected ports resume forwarding without a dual-active state.
- All intended links join the same logical bundle and traffic is distributed without individual member flaps.
Explanation
Correct Answer
D:All intended links join the same logical bundle and traffic is distributed without individual member flaps. This result tests the original failure rather than reporting merely that the configuration command was accepted. LACP aggregates only compatible interfaces, and inconsistent operational settings can suspend members. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence.
Incorrect Answers
A:The intended root remains stable, the active forwarding path operates and the redundant link converges after a fault. This concerns rstp blocked uplink, not lacp member mismatch.
B:The pair reaches Full state and the intended prefixes appear in the OSPF route table without new adjacency flaps. This concerns OSPF area compatibility, not lacp member mismatch.
C:Peer-link adjacency and vPC consistency return healthy, and affected ports resume forwarding without a dual-active state. This concerns vpc peer-link recovery, not lacp member mismatch.
Question 268
An Ansible fabric playbook reports hundreds of changed interfaces on every run even when no administrator intended a configuration change. A scheduled deployment is pending, and the engineer must validate how the script handles this failure condition. What should the engineer do first to address the observed failure?
- Replace non-idempotent imperative commands with state-aware configuration modules and diff-based validation where supported.
- Implement documented pagination and response-error handling in the inventory API client.
- Constrain automation targets using verified site identity and a preflight plan before bulk deployment.
- Validate the DHCP options, image/script availability and bootstrap transport path before restarting POAP.
Explanation
Correct Answer
A:Replace non-idempotent imperative commands with state-aware configuration modules and diff-based validation where supported. Declarative, state-aware automation should converge on the desired configuration without producing repeated unnecessary changes. A scheduled deployment is pending, and the engineer must validate how the script handles this failure condition.
Incorrect Answers
B:Implement documented pagination and response-error handling in the inventory API client. This concerns python api pagination, not ansible idempotent templates.
C:Constrain automation targets using verified site identity and a preflight plan before bulk deployment. This concerns nexus dashboard automation scope, not ansible idempotent templates.
D:Validate the DHCP options, image/script availability and bootstrap transport path before restarting POAP. This concerns poap bootstrap dependencies, not ansible idempotent templates.
Question 269
A SAN change places multiple unrelated hosts and several targets in one broad Fibre Channel zone to simplify access. A storage change board requires a traceable diagnosis before allowing further fabric changes. Which controlled change is most appropriate given the evidence?
- Check the CFS distribution scope and commit or activation workflow for the affected feature.
- Activate the intended zoneset on the correct VSAN and validate its active membership.
- Investigate the physical FC link and its error counters before changing storage service QoS.
- Apply a least-privilege zoning design with an individual initiator and explicitly approved target members per zone.
Explanation
Correct Answer
D:Apply a least-privilege zoning design with an individual initiator and explicitly approved target members per zone. Tightly scoped FC zones limit which initiators can discover or communicate with designated targets. A storage change board requires a traceable diagnosis before allowing further fabric changes.
Incorrect Answers
A:Check the CFS distribution scope and commit or activation workflow for the affected feature. That response is associated with cisco fabric services distribution rather than the specific single-initiator zoning condition described here. For the stated failure, the preferred action is: Apply a least-privilege zoning design with an individual initiator and explicitly approved target members per zone. Relevant evidence: Inspect active zone members, initiator WWPNs, target WWPNs and intended host-to-LUN access matrices. A storage change board requires a traceable diagnosis before allowing further fabric changes.
B:Activate the intended zoneset on the correct VSAN and validate its active membership. That response is associated with zoneset activation state rather than the specific single-initiator zoning condition described here. For the stated failure, the preferred action is: Apply a least-privilege zoning design with an individual initiator and explicitly approved target members per zone. Relevant evidence: Inspect active zone members, initiator WWPNs, target WWPNs and intended host-to-LUN access matrices. A storage change board requires a traceable diagnosis before allowing further fabric changes.
C:Investigate the physical FC link and its error counters before changing storage service QoS. This concerns SAN port error telemetry, not single-initiator zoning.
Question 270
A new VXLAN leaf advertises local VNIs but tunnels to another leaf fail because the VTEP source loopback is missing from underlay routing. The team is preparing a controlled production change and must preserve fabric reachability. Which explanation most directly accounts for the required correction?
- Model-driven telemetry can provide pushed state updates more frequently than coarse periodic polling.
- VXLAN encapsulation depends on routable IP transport between VTEP endpoints before tenant traffic can traverse it.
- Unknown-unicast, broadcast and multicast frames require an appropriate VXLAN replication or multicast transport method.
- An FHRP keeps a virtual default gateway available while members transition between active and standby roles.
Explanation
Correct Answer
B:VXLAN encapsulation depends on routable IP transport between VTEP endpoints before tenant traffic can traverse it. The team is preparing a controlled production change and must preserve fabric reachability.
Incorrect Answers
A:Model-driven telemetry can provide pushed state updates more frequently than coarse periodic polling. This concerns streaming telemetry health, not vxlan vtep underlay reachability.
C:Unknown-unicast, broadcast and multicast frames require an appropriate VXLAN replication or multicast transport method. This concerns bum replication behavior, not vxlan vtep underlay reachability.
D:An FHRP keeps a virtual default gateway available while members transition between active and standby roles. This concerns first-hop gateway failover, not vxlan vtep underlay reachability.
Implementing and Operating Cisco Data Center Core Technologies (DCCOR) (350-601) Practice Tests