Pass Your Juniper JN0-364 Exam Easy!

Juniper JN0-364 Exam Questions & Answers, Accurate & Verified By IT Experts

Instant Download, Free Fast Updates, 99.6% Pass Rate

JN0-364 Premium VCE File

Juniper JN0-364 Premium File

69 Questions & Answers

Last Update: Oct 24, 2026

$69.99

JN0-364 Bundle gives you unlimited access to "JN0-364" files. However, this does not replace the need for a .vce exam simulator. To download VCE exam simulator click here
JN0-364 Premium VCE File
Juniper JN0-364 Premium File

69 Questions & Answers

Last Update: Oct 24, 2026

$69.99

Juniper JN0-364 Exam Bundle gives you unlimited access to "JN0-364" files. However, this does not replace the need for a .vce exam simulator. To download your .vce exam simulator click here

Juniper JN0-364 Practice Test 92

Question 910

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: Two IPv6-only customer islands must communicate across an IPv4 underlay, but no tunnel endpoints have been configured for their routed IPv6 traffic. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Check BGP families, IPv6 route filters and next-hop resolution on each dual-stack peer.
  2. Test both outer IPv4 reachability and inner IPv6 routes during tunnel maintenance.
  3. Inspect both protocol levels' IPv6 TLV propagation during dual-stack deployments.
  4. Exercise large-packet IPv6 and PMTU tests through tunneled or low-MTU paths.

Explanation

Correct Answer

B:

Test both outer IPv4 reachability and inner IPv6 routes during tunnel maintenance. The current controlled acceptance rehearsal demonstrates why this check matters: Two IPv6-only customer islands must communicate across an IPv4 underlay, but no tunnel endpoints have been configured for their routed IPv6 traffic. It monitors the mechanism that An encapsulating tunnel can transport IPv6 payload packets over an IPv4 underlay when endpoint and route mapping are correct. The continuing safeguard should be correlated with the specific acceptance test: An IPv6 trace crosses the intended tunnel, while outer IPv4 packets reach the peer endpoints and encapsulation counters increment.

Incorrect Answers

A:

Check BGP families, IPv6 route filters and next-hop resolution on each dual-stack peer. This control addresses the distinct IPv6 BGP NLRI family omitted operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two IPv6-only customer islands must communicate across an IPv4 underlay, but no tunnel endpoints have been configured for their routed IPv6 traffic. The directly relevant continuing check is: Test both outer IPv4 reachability and inner IPv6 routes during tunnel maintenance. The governing mechanism is: An encapsulating tunnel can transport IPv6 payload packets over an IPv4 underlay when endpoint and route mapping are correct.

C:

Inspect both protocol levels' IPv6 TLV propagation during dual-stack deployments. This control addresses the distinct IS-IS IPv6 reachability TLVs operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two IPv6-only customer islands must communicate across an IPv4 underlay, but no tunnel endpoints have been configured for their routed IPv6 traffic. The directly relevant continuing check is: Test both outer IPv4 reachability and inner IPv6 routes during tunnel maintenance. The governing mechanism is: An encapsulating tunnel can transport IPv6 payload packets over an IPv4 underlay when endpoint and route mapping are correct.

D:

Exercise large-packet IPv6 and PMTU tests through tunneled or low-MTU paths. This control addresses the distinct ICMPv6 packet-too-big handling operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two IPv6-only customer islands must communicate across an IPv4 underlay, but no tunnel endpoints have been configured for their routed IPv6 traffic. The directly relevant continuing check is: Test both outer IPv4 reachability and inner IPv6 routes during tunnel maintenance. The governing mechanism is: An encapsulating tunnel can transport IPv6 payload packets over an IPv4 underlay when endpoint and route mapping are correct.

Question 911

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: A service prefix is missing from peer IS-IS tables after a customer migration because no controlled export policy permits it. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Audit IS-IS route advertisements against customer import and export inventories.
  2. Baseline metric-style compatibility before area-wide IS-IS cost adjustments.
  3. Record DIS priorities and pseudonode behavior in service-provider switching design reviews.
  4. Stage IS-IS key rotations with overlap and rollback checks wherever supported.

Explanation

Correct Answer

A:

Audit IS-IS route advertisements against customer import and export inventories. The current controlled acceptance rehearsal demonstrates why this check matters: A service prefix is missing from peer IS-IS tables after a customer migration because no controlled export policy permits it. It monitors the mechanism that IS-IS export policy controls which eligible non-IS-IS routes can be redistributed into the link-state domain. The continuing safeguard should be correlated with the specific acceptance test: The intended prefix appears at the expected level without management or unrelated customer routes being leaked.

Incorrect Answers

B:

Baseline metric-style compatibility before area-wide IS-IS cost adjustments. This control addresses the distinct IS-IS narrow metric ceiling operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A service prefix is missing from peer IS-IS tables after a customer migration because no controlled export policy permits it. The directly relevant continuing check is: Audit IS-IS route advertisements against customer import and export inventories. The governing mechanism is: IS-IS export policy controls which eligible non-IS-IS routes can be redistributed into the link-state domain.

C:

Record DIS priorities and pseudonode behavior in service-provider switching design reviews. This control addresses the distinct IS-IS DIS election surprise operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A service prefix is missing from peer IS-IS tables after a customer migration because no controlled export policy permits it. The directly relevant continuing check is: Audit IS-IS route advertisements against customer import and export inventories. The governing mechanism is: IS-IS export policy controls which eligible non-IS-IS routes can be redistributed into the link-state domain.

D:

Stage IS-IS key rotations with overlap and rollback checks wherever supported. This control addresses the distinct IS-IS authentication mismatch operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A service prefix is missing from peer IS-IS tables after a customer migration because no controlled export policy permits it. The directly relevant continuing check is: Audit IS-IS route advertisements against customer import and export inventories. The governing mechanism is: IS-IS export policy controls which eligible non-IS-IS routes can be redistributed into the link-state domain.

Question 912

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: A static backup path remains attractive during a fiber failure even though the far-end device cannot forward onward; link-state alone is insufficient to detect reachability. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Test covered and uncovered address samples as part of aggregate change validation.
  2. Maintain a documented martian and bogon-address policy aligned with assigned network ranges.
  3. Review import/export scope and route-copy audits when new routing instances are introduced.
  4. Exercise backup-path liveness detection under downstream and local failure scenarios.

Explanation

Correct Answer

D:

Exercise backup-path liveness detection under downstream and local failure scenarios. The current controlled acceptance rehearsal demonstrates why this check matters: A static backup path remains attractive during a fiber failure even though the far-end device cannot forward onward; link-state alone is insufficient to detect reachability. It monitors the mechanism that A static next hop may appear link-reachable while the remote end-to-end path is unusable, so a tracking mechanism such as BFD can be necessary. The continuing safeguard should be correlated with the specific acceptance test: With the downstream fault injected, the unsuitable backup route is withdrawn or de-preferred and valid traffic moves to the tested alternate.

Incorrect Answers

A:

Test covered and uncovered address samples as part of aggregate change validation. This control addresses the distinct Aggregate rejection behavior operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A static backup path remains attractive during a fiber failure even though the far-end device cannot forward onward; link-state alone is insufficient to detect reachability. The directly relevant continuing check is: Exercise backup-path liveness detection under downstream and local failure scenarios. The governing mechanism is: A static next hop may appear link-reachable while the remote end-to-end path is unusable, so a tracking mechanism such as BFD can be necessary.

B:

Maintain a documented martian and bogon-address policy aligned with assigned network ranges. This control addresses the distinct Martian-address acceptance operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A static backup path remains attractive during a fiber failure even though the far-end device cannot forward onward; link-state alone is insufficient to detect reachability. The directly relevant continuing check is: Exercise backup-path liveness detection under downstream and local failure scenarios. The governing mechanism is: A static next hop may appear link-reachable while the remote end-to-end path is unusable, so a tracking mechanism such as BFD can be necessary.

C:

Review import/export scope and route-copy audits when new routing instances are introduced. This control addresses the distinct RIB group forwarding copy operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A static backup path remains attractive during a fiber failure even though the far-end device cannot forward onward; link-state alone is insufficient to detect reachability. The directly relevant continuing check is: Exercise backup-path liveness detection under downstream and local failure scenarios. The governing mechanism is: A static next hop may appear link-reachable while the remote end-to-end path is unusable, so a tracking mechanism such as BFD can be necessary.

Question 913

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: Two provider switches have a working physical trunk, but VLAN 340 traffic is missing because VLAN 340 is not permitted on the receiving trunk port. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Audit VLAN-to-IRB bindings and routed interfaces during new service activation.
  2. Monitor unknown-unicast rate together with MAC-table learning and churn.
  3. Audit allowed VLAN sets per service and test tagged membership during changes.
  4. Reconcile customer port VLAN membership against service orders after provisioning.

Explanation

Correct Answer

C:

Audit allowed VLAN sets per service and test tagged membership during changes. The current controlled acceptance rehearsal demonstrates why this check matters: Two provider switches have a working physical trunk, but VLAN 340 traffic is missing because VLAN 340 is not permitted on the receiving trunk port. It monitors the mechanism that A trunk transports tagged VLANs only when both ends consistently permit and recognize the VLAN identifiers. The continuing safeguard should be correlated with the specific acceptance test: VLAN 340 MAC learning and tagged traffic are observed on the intended trunk without accidentally carrying other customer VLANs.

Incorrect Answers

A:

Audit VLAN-to-IRB bindings and routed interfaces during new service activation. This control addresses the distinct IRB routed gateway missing operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two provider switches have a working physical trunk, but VLAN 340 traffic is missing because VLAN 340 is not permitted on the receiving trunk port. The directly relevant continuing check is: Audit allowed VLAN sets per service and test tagged membership during changes. The governing mechanism is: A trunk transports tagged VLANs only when both ends consistently permit and recognize the VLAN identifiers.

B:

Monitor unknown-unicast rate together with MAC-table learning and churn. This control addresses the distinct Unknown unicast flooding behavior operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two provider switches have a working physical trunk, but VLAN 340 traffic is missing because VLAN 340 is not permitted on the receiving trunk port. The directly relevant continuing check is: Audit allowed VLAN sets per service and test tagged membership during changes. The governing mechanism is: A trunk transports tagged VLANs only when both ends consistently permit and recognize the VLAN identifiers.

D:

Reconcile customer port VLAN membership against service orders after provisioning. This control addresses the distinct Access VLAN membership operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two provider switches have a working physical trunk, but VLAN 340 traffic is missing because VLAN 340 is not permitted on the receiving trunk port. The directly relevant continuing check is: Audit allowed VLAN sets per service and test tagged membership during changes. The governing mechanism is: A trunk transports tagged VLANs only when both ends consistently permit and recognize the VLAN identifiers.

Question 914

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: After a provider switch reboot, the wrong access switch becomes the STP root because its bridge identifier is lower than the intended core root's ID. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Exercise RSTP role transition in planned failover tests.
  2. Review STP root and backup priorities after device replacement or MAC changes.
  3. Compare MSTP region configuration and digests on each addition or VLAN change.
  4. Review spanning-tree instance resource limits and per-VLAN path placement during capacity changes.

Explanation

Correct Answer

B:

Review STP root and backup priorities after device replacement or MAC changes. The current controlled acceptance rehearsal demonstrates why this check matters: After a provider switch reboot, the wrong access switch becomes the STP root because its bridge identifier is lower than the intended core root's ID. It monitors the mechanism that Spanning-tree root election chooses the lowest bridge ID, which includes configured priority and MAC address. The continuing safeguard should be correlated with the specific acceptance test: The intended core device is reported as root and a designated backup root is stable after an election test.

Incorrect Answers

A:

Exercise RSTP role transition in planned failover tests. This control addresses the distinct RSTP alternate port activation operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: After a provider switch reboot, the wrong access switch becomes the STP root because its bridge identifier is lower than the intended core root's ID. The directly relevant continuing check is: Review STP root and backup priorities after device replacement or MAC changes. The governing mechanism is: Spanning-tree root election chooses the lowest bridge ID, which includes configured priority and MAC address.

C:

Compare MSTP region configuration and digests on each addition or VLAN change. This control addresses the distinct MSTP region mismatch operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: After a provider switch reboot, the wrong access switch becomes the STP root because its bridge identifier is lower than the intended core root's ID. The directly relevant continuing check is: Review STP root and backup priorities after device replacement or MAC changes. The governing mechanism is: Spanning-tree root election chooses the lowest bridge ID, which includes configured priority and MAC address.

D:

Review spanning-tree instance resource limits and per-VLAN path placement during capacity changes. This control addresses the distinct Per-VLAN spanning-tree path operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: After a provider switch reboot, the wrong access switch becomes the STP root because its bridge identifier is lower than the intended core root's ID. The directly relevant continuing check is: Review STP root and backup priorities after device replacement or MAC changes. The governing mechanism is: Spanning-tree root election chooses the lowest bridge ID, which includes configured priority and MAC address.

Question 915

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: Two peering routers have matching AS and neighbor addresses but the BGP session never leaves Connect because traffic to TCP port 179 is blocked along the underlay. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Review inbound prefix filtering and max-route thresholds with every peer change.
  2. Check peer-specific TCP reachability and filtering during peering change control.
  3. Audit route-reflector cluster design and iBGP full-mesh requirements as peer counts grow.
  4. Record negotiated BGP timers and correlate flap events with packet-loss telemetry.

Explanation

Correct Answer

B:

Check peer-specific TCP reachability and filtering during peering change control. The current controlled acceptance rehearsal demonstrates why this check matters: Two peering routers have matching AS and neighbor addresses but the BGP session never leaves Connect because traffic to TCP port 179 is blocked along the underlay. It monitors the mechanism that BGP peers establish a TCP session before exchanging OPEN, KEEPALIVE and UPDATE messages; blocked TCP connectivity prevents peering. The continuing safeguard should be correlated with the specific acceptance test: A TCP session is established to the correct neighbor address, BGP reaches Established and intended routes are exchanged.

Incorrect Answers

A:

Review inbound prefix filtering and max-route thresholds with every peer change. This control addresses the distinct BGP import policy leak operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two peering routers have matching AS and neighbor addresses but the BGP session never leaves Connect because traffic to TCP port 179 is blocked along the underlay. The directly relevant continuing check is: Check peer-specific TCP reachability and filtering during peering change control. The governing mechanism is: BGP peers establish a TCP session before exchanging OPEN, KEEPALIVE and UPDATE messages; blocked TCP connectivity prevents peering.

C:

Audit route-reflector cluster design and iBGP full-mesh requirements as peer counts grow. This control addresses the distinct IBGP transit split horizon operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two peering routers have matching AS and neighbor addresses but the BGP session never leaves Connect because traffic to TCP port 179 is blocked along the underlay. The directly relevant continuing check is: Check peer-specific TCP reachability and filtering during peering change control. The governing mechanism is: BGP peers establish a TCP session before exchanging OPEN, KEEPALIVE and UPDATE messages; blocked TCP connectivity prevents peering.

D:

Record negotiated BGP timers and correlate flap events with packet-loss telemetry. This control addresses the distinct BGP peer flap from mismatched hold timers operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two peering routers have matching AS and neighbor addresses but the BGP session never leaves Connect because traffic to TCP port 179 is blocked along the underlay. The directly relevant continuing check is: Check peer-specific TCP reachability and filtering during peering change control. The governing mechanism is: BGP peers establish a TCP session before exchanging OPEN, KEEPALIVE and UPDATE messages; blocked TCP connectivity prevents peering.

Question 916

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: An SR-MPLS shortest-path LSP is expected, but the source has no usable advertised segment identifier for the target core node. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Document expected label stacks at ingress, transit and penultimate hop for key services.
  2. Track reserved and unreserved bandwidth on TE links before new LSP provisioning.
  3. Audit SID allocations, uniqueness and IGP propagation during segment-routing rollouts.
  4. Rehearse RSVP protection paths during maintenance and monitor bypass readiness.

Explanation

Correct Answer

C:

Audit SID allocations, uniqueness and IGP propagation during segment-routing rollouts. The current controlled acceptance rehearsal demonstrates why this check matters: An SR-MPLS shortest-path LSP is expected, but the source has no usable advertised segment identifier for the target core node. It monitors the mechanism that SR-MPLS forwarding depends on consistent segment identification and an IGP-distributed mapping from segments to MPLS labels. The continuing safeguard should be correlated with the specific acceptance test: The segment identifier is visible in the IGP database, resolves to the correct label, and traffic reaches the selected node.

Incorrect Answers

A:

Document expected label stacks at ingress, transit and penultimate hop for key services. This control addresses the distinct Penultimate hop popping operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: An SR-MPLS shortest-path LSP is expected, but the source has no usable advertised segment identifier for the target core node. The directly relevant continuing check is: Audit SID allocations, uniqueness and IGP propagation during segment-routing rollouts. The governing mechanism is: SR-MPLS forwarding depends on consistent segment identification and an IGP-distributed mapping from segments to MPLS labels.

B:

Track reserved and unreserved bandwidth on TE links before new LSP provisioning. This control addresses the distinct RSVP reservable bandwidth shortage operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: An SR-MPLS shortest-path LSP is expected, but the source has no usable advertised segment identifier for the target core node. The directly relevant continuing check is: Audit SID allocations, uniqueness and IGP propagation during segment-routing rollouts. The governing mechanism is: SR-MPLS forwarding depends on consistent segment identification and an IGP-distributed mapping from segments to MPLS labels.

D:

Rehearse RSVP protection paths during maintenance and monitor bypass readiness. This control addresses the distinct RSVP link protection plan operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: An SR-MPLS shortest-path LSP is expected, but the source has no usable advertised segment identifier for the target core node. The directly relevant continuing check is: Audit SID allocations, uniqueness and IGP propagation during segment-routing rollouts. The governing mechanism is: SR-MPLS forwarding depends on consistent segment identification and an IGP-distributed mapping from segments to MPLS labels.

Question 917

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: A filter-based forwarding policy routes all service traffic into a measurement instance because a broad first term accepts packets before the narrower intended match. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Track ECMP next-hop count and routing-cost drift after transport changes.
  2. Review first-match precedence with representative negative and positive traffic tests.
  3. Use multi-flow telemetry and documented hashing expectations when evaluating ECMP efficiency.
  4. Exercise backup-path liveness detection under downstream and local failure scenarios.

Explanation

Correct Answer

B:

Review first-match precedence with representative negative and positive traffic tests. The current controlled acceptance rehearsal demonstrates why this check matters: A filter-based forwarding policy routes all service traffic into a measurement instance because a broad first term accepts packets before the narrower intended match. It monitors the mechanism that Ordered firewall-filter terms apply the first matching action; overbroad early terms can shadow later selective forwarding rules. The continuing safeguard should be correlated with the specific acceptance test: Matched and unmatched packet samples increment their intended counters and resolve to the expected respective routing tables.

Incorrect Answers

A:

Track ECMP next-hop count and routing-cost drift after transport changes. This control addresses the distinct Equal-cost multipath eligibility operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A filter-based forwarding policy routes all service traffic into a measurement instance because a broad first term accepts packets before the narrower intended match. The directly relevant continuing check is: Review first-match precedence with representative negative and positive traffic tests. The governing mechanism is: Ordered firewall-filter terms apply the first matching action; overbroad early terms can shadow later selective forwarding rules.

C:

Use multi-flow telemetry and documented hashing expectations when evaluating ECMP efficiency. This control addresses the distinct Per-flow hash expectation operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A filter-based forwarding policy routes all service traffic into a measurement instance because a broad first term accepts packets before the narrower intended match. The directly relevant continuing check is: Review first-match precedence with representative negative and positive traffic tests. The governing mechanism is: Ordered firewall-filter terms apply the first matching action; overbroad early terms can shadow later selective forwarding rules.

D:

Exercise backup-path liveness detection under downstream and local failure scenarios. This control addresses the distinct Static backup blackhole operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A filter-based forwarding policy routes all service traffic into a measurement instance because a broad first term accepts packets before the narrower intended match. The directly relevant continuing check is: Review first-match precedence with representative negative and positive traffic tests. The governing mechanism is: Ordered firewall-filter terms apply the first matching action; overbroad early terms can shadow later selective forwarding rules.

Question 918

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: Two routers have interface-based GRE tunnels, but the source address on one end does not match the destination configured on the remote end. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Audit source/destination tunnel-pair symmetry during new GRE turn-ups.
  2. Monitor underlay reachability independently from tunnel interface administrative state.
  3. Include encapsulation overhead in tunnel MTU and traffic acceptance tests.
  4. Document encryption requirements separately from GRE connectivity requirements.

Explanation

Correct Answer

A:

Audit source/destination tunnel-pair symmetry during new GRE turn-ups. The current controlled acceptance rehearsal demonstrates why this check matters: Two routers have interface-based GRE tunnels, but the source address on one end does not match the destination configured on the remote end. It monitors the mechanism that GRE encapsulation uses configured outer source and destination IP addresses, which must align with the underlay endpoints of the intended tunnel. The continuing safeguard should be correlated with the specific acceptance test: Packet captures show the expected outer GRE addresses and matching decapsulation counts on the peer.

Incorrect Answers

B:

Monitor underlay reachability independently from tunnel interface administrative state. This control addresses the distinct GRE underlay recursive loss operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two routers have interface-based GRE tunnels, but the source address on one end does not match the destination configured on the remote end. The directly relevant continuing check is: Audit source/destination tunnel-pair symmetry during new GRE turn-ups. The governing mechanism is: GRE encapsulation uses configured outer source and destination IP addresses, which must align with the underlay endpoints of the intended tunnel.

C:

Include encapsulation overhead in tunnel MTU and traffic acceptance tests. This control addresses the distinct GRE encapsulation MTU overhead operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two routers have interface-based GRE tunnels, but the source address on one end does not match the destination configured on the remote end. The directly relevant continuing check is: Audit source/destination tunnel-pair symmetry during new GRE turn-ups. The governing mechanism is: GRE encapsulation uses configured outer source and destination IP addresses, which must align with the underlay endpoints of the intended tunnel.

D:

Document encryption requirements separately from GRE connectivity requirements. This control addresses the distinct GRE confidentiality misconception operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: Two routers have interface-based GRE tunnels, but the source address on one end does not match the destination configured on the remote end. The directly relevant continuing check is: Audit source/destination tunnel-pair symmetry during new GRE turn-ups. The governing mechanism is: GRE encapsulation uses configured outer source and destination IP addresses, which must align with the underlay endpoints of the intended tunnel.

Question 919

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: A critical RSVP LSP briefly drops after a transit link fails because its designated bypass or fast reroute protection was never established. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Rehearse RSVP protection paths during maintenance and monitor bypass readiness.
  2. Document expected label stacks at ingress, transit and penultimate hop for key services.
  3. Verify label disposition and QoS handling at MPLS egress boundaries after policy changes.
  4. Audit SID allocations, uniqueness and IGP propagation during segment-routing rollouts.

Explanation

Correct Answer

A:

Rehearse RSVP protection paths during maintenance and monitor bypass readiness. The current controlled acceptance rehearsal demonstrates why this check matters: A critical RSVP LSP briefly drops after a transit link fails because its designated bypass or fast reroute protection was never established. It monitors the mechanism that RSVP-TE fast reroute can pre-establish bypass protection for a failure, reducing convergence delay when the main path is lost. The continuing safeguard should be correlated with the specific acceptance test: The bypass LSP is operational before fault injection and protected traffic follows the bypass after the link is disabled.

Incorrect Answers

B:

Document expected label stacks at ingress, transit and penultimate hop for key services. This control addresses the distinct Penultimate hop popping operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A critical RSVP LSP briefly drops after a transit link fails because its designated bypass or fast reroute protection was never established. The directly relevant continuing check is: Rehearse RSVP protection paths during maintenance and monitor bypass readiness. The governing mechanism is: RSVP-TE fast reroute can pre-establish bypass protection for a failure, reducing convergence delay when the main path is lost.

C:

Verify label disposition and QoS handling at MPLS egress boundaries after policy changes. This control addresses the distinct Explicit-null forwarding operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A critical RSVP LSP briefly drops after a transit link fails because its designated bypass or fast reroute protection was never established. The directly relevant continuing check is: Rehearse RSVP protection paths during maintenance and monitor bypass readiness. The governing mechanism is: RSVP-TE fast reroute can pre-establish bypass protection for a failure, reducing convergence delay when the main path is lost.

D:

Audit SID allocations, uniqueness and IGP propagation during segment-routing rollouts. This control addresses the distinct Segment routing SID advertisement operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: A critical RSVP LSP briefly drops after a transit link fails because its designated bypass or fast reroute protection was never established. The directly relevant continuing check is: Rehearse RSVP protection paths during maintenance and monitor bypass readiness. The governing mechanism is: RSVP-TE fast reroute can pre-establish bypass protection for a failure, reducing convergence delay when the main path is lost.

Question 920

During a controlled acceptance rehearsal of the same defect on a separate test network, engineers observe: One aggregated Ethernet member is physically up but never bundles because the link partner's LACP identity or configured aggregation key differs. Which ongoing validation or operating control most directly prevents this specific failure from recurring?

  1. Audit LACP partner identity and collecting/distributing state during bundle maintenance.
  2. Baseline BFD timer settings by platform and monitor false-flap trends.
  3. Test control-plane and data-plane continuity separately under planned RE switchovers.
  4. Audit NSR state and replicate routing databases before maintenance windows.

Explanation

Correct Answer

A:

Audit LACP partner identity and collecting/distributing state during bundle maintenance. The current controlled acceptance rehearsal demonstrates why this check matters: One aggregated Ethernet member is physically up but never bundles because the link partner's LACP identity or configured aggregation key differs. It monitors the mechanism that LACP selects compatible physical links into a logical aggregate based on partner system and aggregation parameters, not carrier alone. The continuing safeguard should be correlated with the specific acceptance test: All intended members show collecting and distributing state in the correct AE bundle and packet forwarding is stable.

Incorrect Answers

B:

Baseline BFD timer settings by platform and monitor false-flap trends. This control addresses the distinct BFD detect timer too aggressive operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: One aggregated Ethernet member is physically up but never bundles because the link partner's LACP identity or configured aggregation key differs. The directly relevant continuing check is: Audit LACP partner identity and collecting/distributing state during bundle maintenance. The governing mechanism is: LACP selects compatible physical links into a logical aggregate based on partner system and aggregation parameters, not carrier alone.

C:

Test control-plane and data-plane continuity separately under planned RE switchovers. This control addresses the distinct GRES forwarding versus routing continuity operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: One aggregated Ethernet member is physically up but never bundles because the link partner's LACP identity or configured aggregation key differs. The directly relevant continuing check is: Audit LACP partner identity and collecting/distributing state during bundle maintenance. The governing mechanism is: LACP selects compatible physical links into a logical aggregate based on partner system and aggregation parameters, not carrier alone.

D:

Audit NSR state and replicate routing databases before maintenance windows. This control addresses the distinct NSR backup routing synchronization operational scenario rather than preventing recurrence of the controlled acceptance rehearsal. The observed problem here is: One aggregated Ethernet member is physically up but never bundles because the link partner's LACP identity or configured aggregation key differs. The directly relevant continuing check is: Audit LACP partner identity and collecting/distributing state during bundle maintenance. The governing mechanism is: LACP selects compatible physical links into a logical aggregate based on partner system and aggregation parameters, not carrier alone.


Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

Purchase Individually

JN0-364 Premium File

Premium File
JN0-364 Premium File
69 Q&A
$76.99$69.99

Site Search:

 

VISA, MasterCard, AmericanExpress, UnionPay

SPECIAL OFFER: GET 10% OFF

ExamCollection Premium

ExamCollection Premium Files

Pass your Exam with ExamCollection's PREMIUM files!

  • ExamCollection Certified Safe Files
  • Guaranteed to have ACTUAL Exam Questions
  • Up-to-Date Exam Study Material - Verified by Experts
  • Instant Downloads
Enter Your Email Address to Receive Your 10% Off Discount Code
A Confirmation Link will be sent to this email address to verify your login
We value your privacy. We will not rent or sell your email address

SPECIAL OFFER: GET 10% OFF

Use Discount Code:

MIN10OFF

A confirmation link was sent to your e-mail.
Please check your mailbox for a message from support@examcollection.com and follow the directions.

Next

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.