Question 560
Clients connected to an access switch stop receiving DHCP leases after DHCP snooping is enabled. Security engineering must restore the approved service without relaxing unrelated protection. What should the engineer collect before ruling out other causes?
- Inspect source guard state, DHCP snooping bindings, static exceptions and ingress drop reasons.
- Inspect TACACS+ reachability, AAA method lists, local credentials and access accounting.
- Inspect DAI drop counters, DHCP snooping binding table, static host assignments and ARP inspection logs.
- Inspect DHCP snooping trust configuration, VLAN enrollment, packet drops and server uplink topology.
Explanation
Correct Answer
D:Inspect DHCP snooping trust configuration, VLAN enrollment, packet drops and server uplink topology. These records help distinguish the suspected failure from a superficially similar fault before modifying production. DHCP snooping should accept DHCP server responses from trusted paths while suppressing rogue access-port servers. Security engineering must restore the approved service without relaxing unrelated protection.
Incorrect Answers
A:Inspect source guard state, DHCP snooping bindings, static exceptions and ingress drop reasons. That response is associated with first-hop ip/mac spoof defense rather than the specific dhcp snooping trusted uplink condition described here. For the stated failure, the preferred action is: Mark only the verified DHCP-server-facing interface as trusted and validate the snooping VLAN scope. Relevant evidence: Inspect DHCP snooping trust configuration, VLAN enrollment, packet drops and server uplink topology. Security engineering must restore the approved service without relaxing unrelated protection.
B:Inspect TACACS+ reachability, AAA method lists, local credentials and access accounting. This concerns centralized AAA fallback, not DHCP snooping trusted uplink.
C:Inspect DAI drop counters, DHCP snooping binding table, static host assignments and ARP inspection logs. That response is associated with dynamic arp inspection source of truth rather than the specific dhcp snooping trusted uplink condition described here. For the stated failure, the preferred action is: Mark only the verified DHCP-server-facing interface as trusted and validate the snooping VLAN scope. Relevant evidence: Inspect DHCP snooping trust configuration, VLAN enrollment, packet drops and server uplink topology. Security engineering must restore the approved service without relaxing unrelated protection.
Question 561
A fabric interconnect has never exported its current UCS configuration despite recent service-profile and policy changes. The issue reappears on a second managed host, so the team is checking its effective profiles and hardware state. Which test result best demonstrates restoration of the intended behavior?
- Only the approved profile scope receives the tested update, with unrelated services preserved.
- The host starts from its approved production device through repeated controlled reboots.
- The workload profile attaches only to blades meeting the declared capacity and adapter criteria.
- An authorized operator can locate and validate the backup artifact and restore procedure in a controlled test.
Explanation
Correct Answer
D:An authorized operator can locate and validate the backup artifact and restore procedure in a controlled test. This result tests the original failure rather than reporting merely that the configuration command was accepted. UCS configuration backups retain recovery information for policies and identities and should accompany approved changes. The issue reappears on a second managed host, so the team is checking its effective profiles and hardware state.
Incorrect Answers
A:Only the approved profile scope receives the tested update, with unrelated services preserved. This concerns updating service-profile templates, not UCS management backup.
B:The host starts from its approved production device through repeated controlled reboots. This concerns boot order and removable media, not UCS management backup.
C:The workload profile attaches only to blades meeting the declared capacity and adapter criteria. This concerns server pool qualification, not UCS management backup.
Question 562
A C-Series host repeatedly boots local media even though its approved UCS policy specifies a SAN boot target. The issue reappears on a second managed host, so the team is checking its effective profiles and hardware state. What information should be inspected before the change is applied?
- Inspect effective vNIC templates, VLAN object assignments, LAN uplink trunk allowances and fault logs.
- Inspect MAC pool definitions, reservations, effective vNIC addresses and upstream MAC tables.
- Inspect applied boot policy, device enumeration, SAN LUN presentation and boot logs.
- Inspect vNIC QoS policies, DCB settings if applicable, interface queue drops and upstream class maps.
Explanation
Correct Answer
C:Inspect applied boot policy, device enumeration, SAN LUN presentation and boot logs. These records help distinguish the suspected failure from a superficially similar fault before modifying production. The effective boot order and accessible target devices determine which source a Cisco server attempts during initialization. The issue reappears on a second managed host, so the team is checking its effective profiles and hardware state.
Incorrect Answers
A:Inspect effective vNIC templates, VLAN object assignments, LAN uplink trunk allowances and fault logs. This concerns UCS VLAN pool and template, not c-series boot policy alignment.
B:Inspect MAC pool definitions, reservations, effective vNIC addresses and upstream MAC tables. This concerns UCS mac pool uniqueness, not c-series boot policy alignment.
D:Inspect vNIC QoS policies, DCB settings if applicable, interface queue drops and upstream class maps. This concerns UCS network qos policy, not c-series boot policy alignment.
Question 563
An IPv6 fabric link has global IPv6 addresses but no OSPFv3 adjacency after a replacement uplink was enabled. The team is preparing a controlled production change and must preserve fabric reachability. How should the implementation be validated against the original failure?
- Remote MAC/IP routes appear in the EVPN database and tested inter-VTEP traffic succeeds.
- An OSPFv3 Full adjacency forms and IPv6 prefixes become reachable through the correct next hop.
- The pair reaches Full state and the intended prefixes appear in the OSPF route table without new adjacency flaps.
- The collector receives fresh, structured device state and alerts on a deliberately induced test event.
Explanation
Correct Answer
B:An OSPFv3 Full adjacency forms and IPv6 prefixes become reachable through the correct next hop. This result tests the original failure rather than reporting merely that the configuration command was accepted. OSPFv3 neighbors communicate over IPv6 link-local addresses and require compatible protocol and area settings. The team is preparing a controlled production change and must preserve fabric reachability.
Incorrect Answers
A:Remote MAC/IP routes appear in the EVPN database and tested inter-VTEP traffic succeeds. That response is associated with mp-bgp evpn route learning rather than the specific ospfv3 ipv6 neighbor discovery condition described here. For the stated failure, the preferred action is: Verify OSPFv3 is enabled on the intended interface and that IPv6 link-local reachability and area configuration match. Relevant evidence: Check IPv6 link-local addresses, OSPFv3 interface participation, area settings and protocol packets. The team is preparing a controlled production change and must preserve fabric reachability.
C:The pair reaches Full state and the intended prefixes appear in the OSPF route table without new adjacency flaps. That response is associated with ospf area compatibility rather than the specific ospfv3 ipv6 neighbor discovery condition described here. For the stated failure, the preferred action is: Verify OSPFv3 is enabled on the intended interface and that IPv6 link-local reachability and area configuration match. Relevant evidence: Check IPv6 link-local addresses, OSPFv3 interface participation, area settings and protocol packets. The team is preparing a controlled production change and must preserve fabric reachability.
D:The collector receives fresh, structured device state and alerts on a deliberately induced test event. This concerns streaming telemetry health, not ospfv3 IPv6 neighbor discovery.
Question 564
An operations platform polls hundreds of leaf switches too slowly to detect short control-plane events. The team is preparing a controlled production change and must preserve fabric reachability. Which test result best demonstrates restoration of the intended behavior?
- Traffic flows identify the actual high-volume conversations and support a targeted capacity or policy fix.
- After maintenance, all required components report the intended EPLD versions and forwarding passes health checks.
- The collector receives fresh, structured device state and alerts on a deliberately induced test event.
- Approved templates match both peers, drift exceptions are resolved and service tests remain normal.
Explanation
Correct Answer
C:The collector receives fresh, structured device state and alerts on a deliberately induced test event. This result tests the original failure rather than reporting merely that the configuration command was accepted. Model-driven telemetry can provide pushed state updates more frequently than coarse periodic polling. The team is preparing a controlled production change and must preserve fabric reachability.
Incorrect Answers
A:Traffic flows identify the actual high-volume conversations and support a targeted capacity or policy fix. This concerns netflow traffic attribution, not streaming telemetry health.
B:After maintenance, all required components report the intended EPLD versions and forwarding passes health checks. This concerns epld firmware maintenance, not streaming telemetry health.
D:Approved templates match both peers, drift exceptions are resolved and service tests remain normal. This concerns fabric configuration drift, not streaming telemetry health.
Question 565
A virtualized host can ping the iSCSI target interface but discovers no storage sessions after a switch change. During the next path-failover exercise, the SAN team must confirm the same dependency on the affected VSAN. Which result would best confirm that the remediation worked?
- The approved client mounts the correct export with intended read/write access and no overbroad client allowance.
- The authorized initiator establishes the intended iSCSI sessions and sees the mapped LUN through supported paths.
- Post-update EPLD versions are correct and tested host multipath failover retains service during planned disruption.
- The documented update completes within its approved impact envelope and host paths remain correctly redundant.
Explanation
Correct Answer
B:The authorized initiator establishes the intended iSCSI sessions and sees the mapped LUN through supported paths. This result tests the original failure rather than reporting merely that the configuration command was accepted. iSCSI uses IP transport and initiator-target session controls rather than Fibre Channel fabric login. During the next path-failover exercise, the SAN team must confirm the same dependency on the affected VSAN.
Incorrect Answers
A:The approved client mounts the correct export with intended read/write access and no overbroad client allowance. This concerns nfs export permissions, not iscsi target discovery.
C:Post-update EPLD versions are correct and tested host multipath failover retains service during planned disruption. This concerns mds epld update impact, not iscsi target discovery.
D:The documented update completes within its approved impact envelope and host paths remain correctly redundant. This concerns mds nondisruptive upgrade planning, not iscsi target discovery.
Question 566
A storage administrator zones a host using a node name although the fabric login is registered with a different port identifier. During the next path-failover exercise, the SAN team must confirm the same dependency on the affected VSAN. Which controlled change is most appropriate given the evidence?
- Create and verify separate VSAN assignments for the teams' relevant FC interfaces and zonesets.
- Reconcile FCNS registrations and target identity changes before recreating the entire VSAN.
- Align trunk allowed VSANs and verify the operational VSAN membership end to end.
- Use the correct initiator and target port WWPNs when creating the required zone memberships.
Explanation
Correct Answer
D:Use the correct initiator and target port WWPNs when creating the required zone memberships. Fibre Channel port WWNs identify individual interfaces used by fabric login and zoning policies. During the next path-failover exercise, the SAN team must confirm the same dependency on the affected VSAN.
Incorrect Answers
A:Create and verify separate VSAN assignments for the teams' relevant FC interfaces and zonesets. This concerns VSAN isolation, not wwpn versus wwnn.
B:Reconcile FCNS registrations and target identity changes before recreating the entire VSAN. This concerns fibre channel name-server entries, not wwpn versus wwnn.
C:Align trunk allowed VSANs and verify the operational VSAN membership end to end. This concerns VSAN trunk mismatch, not wwpn versus wwnn.
Question 567
A replacement ACI leaf remains undiscovered after connecting to the spine and giving it management power. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence. Which result would best confirm that the remediation worked?
- The leaf appears as a registered healthy fabric member with the expected role and adjacency.
- Virtual endpoints are learned in the intended EPG and their traffic follows its applied contracts.
- The collector receives fresh, structured device state and alerts on a deliberately induced test event.
- The target encapsulation is programmed on the intended port and endpoint learning succeeds.
Explanation
Correct Answer
A:The leaf appears as a registered healthy fabric member with the expected role and adjacency. This result tests the original failure rather than reporting merely that the configuration command was accepted. An ACI fabric must discover and register infrastructure nodes before normal tenant policy deployment. A second maintenance window is approaching, and the engineer must confirm the same failure mode using current device evidence.
Incorrect Answers
B:Virtual endpoints are learned in the intended EPG and their traffic follows its applied contracts. This concerns aci vmm association, not aci fabric discovery.
C:The collector receives fresh, structured device state and alerts on a deliberately induced test event. This concerns streaming telemetry health, not aci fabric discovery.
D:The target encapsulation is programmed on the intended port and endpoint learning succeeds. This concerns aci access policy chain, not aci fabric discovery.
Question 568
A replacement management cluster is being restored from an old UCS backup while recently issued MAC and WWPN pools may differ. Operations is validating the host before approving production workload placement. What should the engineer do first to address the observed failure?
- Stage and review the template relationship and scope before applying an impactful shared-policy change.
- Correct server-pool qualifications and service-profile placement criteria for the workload's hardware dependencies.
- Validate backup age, identity-pool effects and restore prerequisites before applying the saved configuration.
- Validate the service-profile SAN boot target WWPN/LUN settings and underlying zoning/masking path.
Explanation
Correct Answer
C:Validate backup age, identity-pool effects and restore prerequisites before applying the saved configuration. Restoring UCS management state can reintroduce policy and identity definitions that differ from current infrastructure. Operations is validating the host before approving production workload placement.
Incorrect Answers
A:Stage and review the template relationship and scope before applying an impactful shared-policy change. This concerns updating service-profile templates, not UCS restore integrity.
B:Correct server-pool qualifications and service-profile placement criteria for the workload's hardware dependencies. This concerns server pool qualification, not UCS restore integrity.
D:Validate the service-profile SAN boot target WWPN/LUN settings and underlying zoning/masking path. This concerns SAN boot path policy, not UCS restore integrity.
Question 569
Two production Nexus peers have drifted in their intended interface templates after unreviewed local commands were applied. The team is preparing a controlled production change and must preserve fabric reachability. What should the operator avoid assuming from the observed state?
- Data-plane tunnel reachability does not imply correct import or export of the tenant's EVPN routes.
- A working IPv4 OSPFv2 adjacency does not establish IPv6 OSPFv3 reachability by itself.
- A configuration backup alone does not prove the running state matches approved policy.
- An RP mapping correction will not compensate for broken RPF reachability to the multicast source.
Explanation
Correct Answer
C:A configuration backup alone does not prove the running state matches approved policy. Configuration management detects and remediates unauthorized deviations rather than trusting the most recent device state. The team is preparing a controlled production change and must preserve fabric reachability.
Incorrect Answers
A:Data-plane tunnel reachability does not imply correct import or export of the tenant's EVPN routes. This concerns mp-BGP evpn route learning, not fabric configuration drift.
B:A working IPv4 OSPFv2 adjacency does not establish IPv6 OSPFv3 reachability by itself. This concerns ospfv3 IPv6 neighbor discovery, not fabric configuration drift.
D:An RP mapping correction will not compensate for broken RPF reachability to the multicast source. This concerns PIM multicast rendezvous point, not fabric configuration drift.
Question 570
Clients connected to an access switch stop receiving DHCP leases after DHCP snooping is enabled. A follow-up access review asks the team to validate the same boundary with a controlled negative test. What should the operator avoid assuming from the observed state?
- Trusting all access ports would negate the primary protection against unauthorized DHCP servers.
- Enabling only an ARP inspection check may not validate every IP data packet's source identity.
- Disabling DAI across the whole access VLAN would remove spoofing protection to solve a narrow exception.
- Host-level WWPN zoning is not a substitute for constraining switch-to-switch fabric membership.
Explanation
Correct Answer
A:Trusting all access ports would negate the primary protection against unauthorized DHCP servers. DHCP snooping should accept DHCP server responses from trusted paths while suppressing rogue access-port servers. A follow-up access review asks the team to validate the same boundary with a controlled negative test.
Incorrect Answers
B:Enabling only an ARP inspection check may not validate every IP data packet's source identity. This concerns first-hop ip/mac spoof defense, not DHCP snooping trusted uplink.
C:Disabling DAI across the whole access VLAN would remove spoofing protection to solve a narrow exception. This concerns dynamic ARP inspection source of truth, not DHCP snooping trusted uplink.
D:Host-level WWPN zoning is not a substitute for constraining switch-to-switch fabric membership. This concerns fabric binding membership, not DHCP snooping trusted uplink.
Implementing and Operating Cisco Data Center Core Technologies (DCCOR) (350-601) Practice Tests