Pass Your Juniper JN0-664 Exam Easy!

Juniper JN0-664 Exam Questions & Answers, Accurate & Verified By IT Experts

Instant Download, Free Fast Updates, 99.6% Pass Rate

JN0-664 Premium VCE File

Juniper JN0-664 Premium File

96 Questions & Answers

Last Update: Oct 12, 2026

$69.99

JN0-664 Bundle gives you unlimited access to "JN0-664" files. However, this does not replace the need for a .vce exam simulator. To download VCE exam simulator click here
JN0-664 Premium VCE File
Juniper JN0-664 Premium File

96 Questions & Answers

Last Update: Oct 12, 2026

$69.99

Juniper JN0-664 Exam Bundle gives you unlimited access to "JN0-664" files. However, this does not replace the need for a .vce exam simulator. To download your .vce exam simulator click here

Juniper JN0-664 Practice Test 94

Question 930

During an inter-POP failover test, an HPE Juniper Networking engineer investigates this situation: An EVPN segment carries known unicast correctly but floods no broadcast/unknown-unicast frames to a recently added PE. Which operational control would best prevent a recurrence of this exact failure mode?

  1. Require a loop-free attachment design before adding redundant customer trunks.
  2. Test BUM delivery separately from known-unicast MAC reachability.
  3. Fail over the DF during testing and check for duplicate frames or blackholes.
  4. Test broadcast storm containment before admitting additional VPLS PEs.

Explanation

Correct Answer

B:

Test BUM delivery separately from known-unicast MAC reachability. The control limits repetition of the described root condition: EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. During audits, confirm: Each authorized PE appears in the replication set and controlled BUM test traffic reaches the intended sites.

Incorrect Answers

A:

Require a loop-free attachment design before adding redundant customer trunks. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically VPLS root cause of broadcast storm. An uncontrolled customer Layer 2 loop can amplify flooding throughout a multipoint virtual bridge. In this scenario, however, the distinguishing issue is EVPN inclusive multicast route and the confirming observation is: Each authorized PE appears in the replication set and controlled BUM test traffic reaches the intended sites.

C:

Fail over the DF during testing and check for duplicate frames or blackholes. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically EVPN designated forwarder election. EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment. In this scenario, however, the distinguishing issue is EVPN inclusive multicast route and the confirming observation is: Each authorized PE appears in the replication set and controlled BUM test traffic reaches the intended sites.

D:

Test broadcast storm containment before admitting additional VPLS PEs. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically VPLS split-horizon protection. VPLS needs loop-prevention controls such as split-horizon behavior when forwarding between remote pseudowires. In this scenario, however, the distinguishing issue is EVPN inclusive multicast route and the confirming observation is: Each authorized PE appears in the replication set and controlled BUM test traffic reaches the intended sites.

Question 931

During a new PE-router service turn-up, an HPE Juniper Networking engineer investigates this situation: A customer VLAN is dual-homed to two EVPN PEs and both forward the same broadcast traffic into the same segment, causing duplicates. Which targeted check most directly distinguishes the likely cause before a configuration change?

  1. Inspect EVPN Ethernet auto-discovery type 1 advertisements associated with the shared segment.
  2. Compare ESI values advertised by both PEs and the physical multihoming design.
  3. Inspect Ethernet segment identifier, DF election result and per-VLAN forwarder eligibility.
  4. Inspect EVPN type 3 inclusive multicast route exchange and associated flooding membership.

Explanation

Correct Answer

C:

Inspect Ethernet segment identifier, DF election result and per-VLAN forwarder eligibility. This check examines the decisive condition for EVPN designated forwarder election before any unrelated changes are made. The underlying mechanism is: EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment. The confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

Incorrect Answers

A:

Inspect EVPN Ethernet auto-discovery type 1 advertisements associated with the shared segment. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically EVPN Ethernet AD signaling. Ethernet AD routes help distribute EVPN segment reachability and can support multihoming convergence mechanisms. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

B:

Compare ESI values advertised by both PEs and the physical multihoming design. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically EVPN Ethernet segment identifier mismatch. EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

D:

Inspect EVPN type 3 inclusive multicast route exchange and associated flooding membership. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically EVPN inclusive multicast route. EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

Question 932

During a customer VPN change window, an HPE Juniper Networking engineer investigates this situation: A customer VLAN is dual-homed to two EVPN PEs and both forward the same broadcast traffic into the same segment, causing duplicates. Which routing or service mechanism best explains the reported behavior?

  1. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused.
  2. EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI.
  3. BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide.
  4. EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment.

Explanation

Correct Answer

D:

EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment. This is the causal rule that fits the observed state, not just a correlated symptom. To distinguish it from other failures, look for: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site. The targeted correction is: Align multihoming and DF-election configuration for the shared Ethernet segment.

Incorrect Answers

A:

BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically VPLS route target site leakage. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

B:

EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically EVPN inclusive multicast route. EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

C:

BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically BGP Layer 2 VPN route distinguisher. BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

Question 933

During a core-routing migration rehearsal, an HPE Juniper Networking engineer investigates this situation: A customer VLAN is dual-homed to two EVPN PEs and both forward the same broadcast traffic into the same segment, causing duplicates. After the appropriate response, which observation would best confirm that the stated service condition is handled correctly?

  1. Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.
  2. Remote PEs import the appropriate Ethernet AD signaling and react correctly when one PE withdraws its segment reachability.
  3. Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.
  4. Unrelated remote sites disappear from the VPN membership and their MACs are no longer learned.

Explanation

Correct Answer

A:

Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site. This observation directly tests the fault hypothesis rather than simply showing that a session or interface exists. The underlying reason is: EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment.

Incorrect Answers

B:

Remote PEs import the appropriate Ethernet AD signaling and react correctly when one PE withdraws its segment reachability. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically EVPN Ethernet AD signaling. Ethernet AD routes help distribute EVPN segment reachability and can support multihoming convergence mechanisms. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

C:

Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically EVPN Ethernet segment identifier mismatch. EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

D:

Unrelated remote sites disappear from the VPN membership and their MACs are no longer learned. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically VPLS route target site leakage. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

Question 934

During a backbone POP acceptance review, an HPE Juniper Networking engineer investigates this situation: A customer VLAN is dual-homed to two EVPN PEs and both forward the same broadcast traffic into the same segment, causing duplicates. Which response or focused corrective action best addresses this situation without changing unrelated components?

  1. Correct the supported type 1 Ethernet AD advertisement and import policy for the ESI.
  2. Align multihoming and DF-election configuration for the shared Ethernet segment.
  3. Configure the intended matching ESI with compatible redundancy parameters.
  4. Correct per-tenant route target assignment and BGP import policy.

Explanation

Correct Answer

B:

Align multihoming and DF-election configuration for the shared Ethernet segment. The change addresses the root behavior described here: EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment. Verify success with: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

Incorrect Answers

A:

Correct the supported type 1 Ethernet AD advertisement and import policy for the ESI. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically EVPN Ethernet AD signaling. Ethernet AD routes help distribute EVPN segment reachability and can support multihoming convergence mechanisms. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

C:

Configure the intended matching ESI with compatible redundancy parameters. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically EVPN Ethernet segment identifier mismatch. EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

D:

Correct per-tenant route target assignment and BGP import policy. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically VPLS route target site leakage. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

Question 935

During an overnight NOC investigation, an HPE Juniper Networking engineer investigates this situation: A customer VLAN is dual-homed to two EVPN PEs and both forward the same broadcast traffic into the same segment, causing duplicates. Which operational control would best prevent a recurrence of this exact failure mode?

  1. Validate both all-active reachability and withdrawal during a controlled multihoming failover.
  2. Validate ESI consistency before enabling dual-homed production traffic.
  3. Fail over the DF during testing and check for duplicate frames or blackholes.
  4. Perform negative remote-site membership checks before accepting a VPLS service.

Explanation

Correct Answer

C:

Fail over the DF during testing and check for duplicate frames or blackholes. The control limits repetition of the described root condition: EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment. During audits, confirm: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

Incorrect Answers

A:

Validate both all-active reachability and withdrawal during a controlled multihoming failover. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically EVPN Ethernet AD signaling. Ethernet AD routes help distribute EVPN segment reachability and can support multihoming convergence mechanisms. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

B:

Validate ESI consistency before enabling dual-homed production traffic. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically EVPN Ethernet segment identifier mismatch. EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

D:

Perform negative remote-site membership checks before accepting a VPLS service. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically VPLS route target site leakage. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. In this scenario, however, the distinguishing issue is EVPN designated forwarder election and the confirming observation is: Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.

Question 936

During a high-availability validation, an HPE Juniper Networking engineer investigates this situation: A dual-homed Ethernet site is intended to be one EVPN Ethernet segment but its PEs advertise different ESIs, so remote devices do not treat it as shared. Which targeted check most directly distinguishes the likely cause before a configuration change?

  1. Inspect Ethernet segment reachability advertisements and fast convergence or mass-withdraw behavior.
  2. Inspect Ethernet segment identifier, DF election result and per-VLAN forwarder eligibility.
  3. Inspect BGP L2VPN route distinguishers and the relevant service NLRI.
  4. Compare ESI values advertised by both PEs and the physical multihoming design.

Explanation

Correct Answer

D:

Compare ESI values advertised by both PEs and the physical multihoming design. This check examines the decisive condition for EVPN Ethernet segment identifier mismatch before any unrelated changes are made. The underlying mechanism is: EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment. The confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

Incorrect Answers

A:

Inspect Ethernet segment reachability advertisements and fast convergence or mass-withdraw behavior. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically EVPN multihoming mass withdrawal. EVPN multihoming can signal a PE or segment failure so remote PEs quickly invalidate affected MAC reachability. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

B:

Inspect Ethernet segment identifier, DF election result and per-VLAN forwarder eligibility. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically EVPN designated forwarder election. EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

C:

Inspect BGP L2VPN route distinguishers and the relevant service NLRI. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically BGP Layer 2 VPN route distinguisher. BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

Question 937

During a Junos routing maintenance review, an HPE Juniper Networking engineer investigates this situation: A dual-homed Ethernet site is intended to be one EVPN Ethernet segment but its PEs advertise different ESIs, so remote devices do not treat it as shared. Which routing or service mechanism best explains the reported behavior?

  1. EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment.
  2. EVPN multihoming can signal a PE or segment failure so remote PEs quickly invalidate affected MAC reachability.
  3. BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide.
  4. VPLS signaling design determines how remote sites are discovered and how service labels are exchanged.

Explanation

Correct Answer

A:

EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment. This is the causal rule that fits the observed state, not just a correlated symptom. To distinguish it from other failures, look for: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment. The targeted correction is: Configure the intended matching ESI with compatible redundancy parameters.

Incorrect Answers

B:

EVPN multihoming can signal a PE or segment failure so remote PEs quickly invalidate affected MAC reachability. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically EVPN multihoming mass withdrawal. EVPN multihoming can signal a PE or segment failure so remote PEs quickly invalidate affected MAC reachability. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

C:

BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically BGP Layer 2 VPN route distinguisher. BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

D:

VPLS signaling design determines how remote sites are discovered and how service labels are exchanged. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically VPLS BGP versus LDP signaling. VPLS signaling design determines how remote sites are discovered and how service labels are exchanged. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

Question 938

During a multisite network cutover, an HPE Juniper Networking engineer investigates this situation: A dual-homed Ethernet site is intended to be one EVPN Ethernet segment but its PEs advertise different ESIs, so remote devices do not treat it as shared. After the appropriate response, which observation would best confirm that the stated service condition is handled correctly?

  1. Remote forwarding moves away from the failed PE after the segment withdrawal or protection event.
  2. Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.
  3. Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site.
  4. Distinct RDs preserve separate advertisements and only correct tenant membership is imported.

Explanation

Correct Answer

B:

Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment. This observation directly tests the fault hypothesis rather than simply showing that a session or interface exists. The underlying reason is: EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment.

Incorrect Answers

A:

Remote forwarding moves away from the failed PE after the segment withdrawal or protection event. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically EVPN multihoming mass withdrawal. EVPN multihoming can signal a PE or segment failure so remote PEs quickly invalidate affected MAC reachability. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

C:

Only the elected eligible DF forwards the relevant BUM traffic toward the dual-homed site. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically EVPN designated forwarder election. EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

D:

Distinct RDs preserve separate advertisements and only correct tenant membership is imported. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically BGP Layer 2 VPN route distinguisher. BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

Question 939

During a metro aggregation incident, an HPE Juniper Networking engineer investigates this situation: A dual-homed Ethernet site is intended to be one EVPN Ethernet segment but its PEs advertise different ESIs, so remote devices do not treat it as shared. Which response or focused corrective action best addresses this situation without changing unrelated components?

  1. Restore the supported Ethernet segment failure signaling and backup forwarding path.
  2. Align multihoming and DF-election configuration for the shared Ethernet segment.
  3. Configure the intended matching ESI with compatible redundancy parameters.
  4. Assign unique appropriate service RDs and verify per-tenant RT imports.

Explanation

Correct Answer

C:

Configure the intended matching ESI with compatible redundancy parameters. The change addresses the root behavior described here: EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment. Verify success with: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

Incorrect Answers

A:

Restore the supported Ethernet segment failure signaling and backup forwarding path. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically EVPN multihoming mass withdrawal. EVPN multihoming can signal a PE or segment failure so remote PEs quickly invalidate affected MAC reachability. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

B:

Align multihoming and DF-election configuration for the shared Ethernet segment. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically EVPN designated forwarder election. EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

D:

Assign unique appropriate service RDs and verify per-tenant RT imports. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically BGP Layer 2 VPN route distinguisher. BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

Question 940

During a managed service audit, an HPE Juniper Networking engineer investigates this situation: A dual-homed Ethernet site is intended to be one EVPN Ethernet segment but its PEs advertise different ESIs, so remote devices do not treat it as shared. Which operational control would best prevent a recurrence of this exact failure mode?

  1. Test PE failure recovery with live MAC entries, not only a ping to the surviving PE.
  2. Fail over the DF during testing and check for duplicate frames or blackholes.
  3. Audit VPN identifiers before consolidating L2VPN routes on shared reflectors.
  4. Validate ESI consistency before enabling dual-homed production traffic.

Explanation

Correct Answer

D:

Validate ESI consistency before enabling dual-homed production traffic. The control limits repetition of the described root condition: EVPN multihoming relies on consistent Ethernet segment identification among PEs attached to the same segment. During audits, confirm: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

Incorrect Answers

A:

Test PE failure recovery with live MAC entries, not only a ping to the surviving PE. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically EVPN multihoming mass withdrawal. EVPN multihoming can signal a PE or segment failure so remote PEs quickly invalidate affected MAC reachability. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

B:

Fail over the DF during testing and check for duplicate frames or blackholes. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically EVPN designated forwarder election. EVPN multihoming uses designated forwarder selection to prevent duplicate BUM forwarding to a shared Ethernet segment. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.

C:

Audit VPN identifiers before consolidating L2VPN routes on shared reflectors. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically BGP Layer 2 VPN route distinguisher. BGP-signaled L2VPN routes need distinguishable VPN identifiers so unrelated overlapping customer service advertisements do not collide. In this scenario, however, the distinguishing issue is EVPN Ethernet segment identifier mismatch and the confirming observation is: Both peers advertise a matching ESI and remote control-plane state recognizes the multi-attached segment.


Service Provider Routing and Switching, Professional (JNCIP-SP) (JN0-664) Practice Tests

Purchase Individually

JN0-664 Premium File

Premium File
JN0-664 Premium File
96 Q&A
$76.99$69.99

Site Search:

 

VISA, MasterCard, AmericanExpress, UnionPay

SPECIAL OFFER: GET 10% OFF

ExamCollection Premium

ExamCollection Premium Files

Pass your Exam with ExamCollection's PREMIUM files!

  • ExamCollection Certified Safe Files
  • Guaranteed to have ACTUAL Exam Questions
  • Up-to-Date Exam Study Material - Verified by Experts
  • Instant Downloads
Enter Your Email Address to Receive Your 10% Off Discount Code
A Confirmation Link will be sent to this email address to verify your login
We value your privacy. We will not rent or sell your email address

SPECIAL OFFER: GET 10% OFF

Use Discount Code:

MIN10OFF

A confirmation link was sent to your e-mail.
Please check your mailbox for a message from support@examcollection.com and follow the directions.

Next

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.