Pass Your Juniper JN0-664 Exam Easy!

Juniper JN0-664 Exam Questions & Answers, Accurate & Verified By IT Experts

Instant Download, Free Fast Updates, 99.6% Pass Rate

JN0-664 Premium VCE File

Juniper JN0-664 Premium File

96 Questions & Answers

Last Update: Oct 12, 2026

$69.99

JN0-664 Bundle gives you unlimited access to "JN0-664" files. However, this does not replace the need for a .vce exam simulator. To download VCE exam simulator click here
JN0-664 Premium VCE File
Juniper JN0-664 Premium File

96 Questions & Answers

Last Update: Oct 12, 2026

$69.99

Juniper JN0-664 Exam Bundle gives you unlimited access to "JN0-664" files. However, this does not replace the need for a .vce exam simulator. To download your .vce exam simulator click here

Juniper JN0-664 Practice Test 66

Question 650

During a customer service restoration, an HPE Juniper Networking engineer investigates this situation: A receiver's source-specific subscription names the wrong source IPv4 address; group state exists but no traffic arrives. Which operational control would best prevent a recurrence of this exact failure mode?

  1. Track RP loopback availability from each multicast island.
  2. Validate channel source and group pairs from the application inventory.
  3. Check IGMP source-filter capability before migrating a group range to SSM.
  4. Test source failover and relocation independently of receiver join success.

Explanation

Correct Answer

B:

Validate channel source and group pairs from the application inventory. The control limits repetition of the described root condition: SSM membership is bound to a source and group pair; membership for the wrong source does not authorize the actual source stream. During audits, confirm: The IGMP (S,G) entry matches the active server's source and packets arrive through the correct RPF interface.

Incorrect Answers

A:

Track RP loopback availability from each multicast island. This is a plausible preventive practice for a different IP Multicast condition, specifically RP unreachable by unicast. PIM joins are sent toward the RP using unicast-derived RPF paths; a configured RP with no route is not usable. In this scenario, however, the distinguishing issue is SSM source address typo and the confirming observation is: The IGMP (S,G) entry matches the active server's source and packets arrive through the correct RPF interface.

C:

Check IGMP source-filter capability before migrating a group range to SSM. This is a plausible preventive practice for a different IP Multicast condition, specifically IGMPv2 limitations for SSM. Native IGMPv3 carries source-specific membership information required for straightforward IPv4 SSM subscriptions. In this scenario, however, the distinguishing issue is SSM source address typo and the confirming observation is: The IGMP (S,G) entry matches the active server's source and packets arrive through the correct RPF interface.

D:

Test source failover and relocation independently of receiver join success. This is a plausible preventive practice for a different IP Multicast condition, specifically ASM shared-tree source loss. A healthy receiver shared tree does not prove the RP has discovered a currently active ASM source. In this scenario, however, the distinguishing issue is SSM source address typo and the confirming observation is: The IGMP (S,G) entry matches the active server's source and packets arrive through the correct RPF interface.

Question 651

During a Junos routing maintenance review, an HPE Juniper Networking engineer investigates this situation: The core can receive source multicast traffic and passes RPF, but an access router has no outgoing interfaces for the group. Which targeted check most directly distinguishes the likely cause before a configuration change?

  1. Inspect PIM Hello counters and interface filtering for the directly connected transit.
  2. Inspect IGMP version and whether the host can express source filters.
  3. Inspect last-hop membership state and the multicast OIL for the destination group.
  4. Compare dense-mode flooding/pruning with sparse-mode explicit join behavior for the service.

Explanation

Correct Answer

C:

Inspect last-hop membership state and the multicast OIL for the destination group. This check examines the decisive condition for Multicast output interface list empty before any unrelated changes are made. The underlying mechanism is: A passing RPF check does not create downstream delivery without an interested outgoing interface. The confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

Incorrect Answers

A:

Inspect PIM Hello counters and interface filtering for the directly connected transit. This is a plausible diagnostic check for a different IP Multicast condition, specifically PIM hello neighbor dead. PIM neighbor discovery requires compatible Hello exchange on every required multicast-routing link. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

B:

Inspect IGMP version and whether the host can express source filters. This is a plausible diagnostic check for a different IP Multicast condition, specifically IGMPv2 limitations for SSM. Native IGMPv3 carries source-specific membership information required for straightforward IPv4 SSM subscriptions. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

D:

Compare dense-mode flooding/pruning with sparse-mode explicit join behavior for the service. This is a plausible diagnostic check for a different IP Multicast condition, specifically Dense-mode flood and prune. Dense mode initially floods along branches and prunes uninterested segments, unlike sparse mode's explicit interest model. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

Question 652

During a multisite network cutover, an HPE Juniper Networking engineer investigates this situation: The core can receive source multicast traffic and passes RPF, but an access router has no outgoing interfaces for the group. Which routing or service mechanism best explains the reported behavior?

  1. PIM neighbor discovery requires compatible Hello exchange on every required multicast-routing link.
  2. Last-hop multicast forwarding depends on maintained group membership; missing queries or membership reports can allow entries to expire.
  3. Native IGMPv3 carries source-specific membership information required for straightforward IPv4 SSM subscriptions.
  4. A passing RPF check does not create downstream delivery without an interested outgoing interface.

Explanation

Correct Answer

D:

A passing RPF check does not create downstream delivery without an interested outgoing interface. This is the causal rule that fits the observed state, not just a correlated symptom. To distinguish it from other failures, look for: The group forwarding entry contains the intended access-facing interface after receiver membership is restored. The targeted correction is: Repair IGMP last-hop membership or PIM downstream join signaling.

Incorrect Answers

A:

PIM neighbor discovery requires compatible Hello exchange on every required multicast-routing link. This is a plausible protocol explanation for a different IP Multicast condition, specifically PIM hello neighbor dead. PIM neighbor discovery requires compatible Hello exchange on every required multicast-routing link. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

B:

Last-hop multicast forwarding depends on maintained group membership; missing queries or membership reports can allow entries to expire. This is a plausible protocol explanation for a different IP Multicast condition, specifically IGMP membership aging. Last-hop multicast forwarding depends on maintained group membership; missing queries or membership reports can allow entries to expire. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

C:

Native IGMPv3 carries source-specific membership information required for straightforward IPv4 SSM subscriptions. This is a plausible protocol explanation for a different IP Multicast condition, specifically IGMPv2 limitations for SSM. Native IGMPv3 carries source-specific membership information required for straightforward IPv4 SSM subscriptions. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

Question 653

During a metro aggregation incident, an HPE Juniper Networking engineer investigates this situation: The core can receive source multicast traffic and passes RPF, but an access router has no outgoing interfaces for the group. After the appropriate response, which observation would best confirm that the stated service condition is handled correctly?

  1. The group forwarding entry contains the intended access-facing interface after receiver membership is restored.
  2. A PIM neighbor forms and downstream join state propagates after the control traffic is allowed.
  3. Observed flooding aligns with dense-mode refresh behavior instead of indicating a new receiver.
  4. A group-specific RP mapping exists and the (*,G) join reaches the mapped RP.

Explanation

Correct Answer

A:

The group forwarding entry contains the intended access-facing interface after receiver membership is restored. This observation directly tests the fault hypothesis rather than simply showing that a session or interface exists. The underlying reason is: A passing RPF check does not create downstream delivery without an interested outgoing interface.

Incorrect Answers

B:

A PIM neighbor forms and downstream join state propagates after the control traffic is allowed. This is a plausible observed evidence for a different IP Multicast condition, specifically PIM hello neighbor dead. PIM neighbor discovery requires compatible Hello exchange on every required multicast-routing link. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

C:

Observed flooding aligns with dense-mode refresh behavior instead of indicating a new receiver. This is a plausible observed evidence for a different IP Multicast condition, specifically PIM dense-mode prune expiry. Dense mode may periodically refresh distribution and prune state, so temporary unwanted traffic can occur before pruning. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

D:

A group-specific RP mapping exists and the (*,G) join reaches the mapped RP. This is a plausible observed evidence for a different IP Multicast condition, specifically PIM sparse RP mapping absent. PIM sparse mode ASM uses an RP mapping for shared-tree joins before source-specific tree behavior may take over. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

Question 654

During a managed service audit, an HPE Juniper Networking engineer investigates this situation: The core can receive source multicast traffic and passes RPF, but an access router has no outgoing interfaces for the group. Which response or focused corrective action best addresses this situation without changing unrelated components?

  1. Restore the minimum authorized PIM control traffic on the affected link.
  2. Repair IGMP last-hop membership or PIM downstream join signaling.
  3. Restore consistent IGMP querier behavior and receiver report processing.
  4. Select sparse mode when the service cannot tolerate periodic uninterested flooding.

Explanation

Correct Answer

B:

Repair IGMP last-hop membership or PIM downstream join signaling. The change addresses the root behavior described here: A passing RPF check does not create downstream delivery without an interested outgoing interface. Verify success with: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

Incorrect Answers

A:

Restore the minimum authorized PIM control traffic on the affected link. This is a plausible configuration or operational fix for a different IP Multicast condition, specifically PIM hello neighbor dead. PIM neighbor discovery requires compatible Hello exchange on every required multicast-routing link. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

C:

Restore consistent IGMP querier behavior and receiver report processing. This is a plausible configuration or operational fix for a different IP Multicast condition, specifically IGMP membership aging. Last-hop multicast forwarding depends on maintained group membership; missing queries or membership reports can allow entries to expire. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

D:

Select sparse mode when the service cannot tolerate periodic uninterested flooding. This is a plausible configuration or operational fix for a different IP Multicast condition, specifically PIM dense-mode prune expiry. Dense mode may periodically refresh distribution and prune state, so temporary unwanted traffic can occur before pruning. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

Question 655

During a network architecture troubleshooting workshop, an HPE Juniper Networking engineer investigates this situation: The core can receive source multicast traffic and passes RPF, but an access router has no outgoing interfaces for the group. Which operational control would best prevent a recurrence of this exact failure mode?

  1. Include protocol control-plane permit tests in multicast transit security reviews.
  2. Monitor membership table ages during endpoint power-save and VLAN changes.
  3. Monitor outgoing-interface lists alongside source packet counters.
  4. Compare observed branch load against actual subscriber distribution before accepting dense mode.

Explanation

Correct Answer

C:

Monitor outgoing-interface lists alongside source packet counters. The control limits repetition of the described root condition: A passing RPF check does not create downstream delivery without an interested outgoing interface. During audits, confirm: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

Incorrect Answers

A:

Include protocol control-plane permit tests in multicast transit security reviews. This is a plausible preventive practice for a different IP Multicast condition, specifically PIM hello neighbor dead. PIM neighbor discovery requires compatible Hello exchange on every required multicast-routing link. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

B:

Monitor membership table ages during endpoint power-save and VLAN changes. This is a plausible preventive practice for a different IP Multicast condition, specifically IGMP membership aging. Last-hop multicast forwarding depends on maintained group membership; missing queries or membership reports can allow entries to expire. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

D:

Compare observed branch load against actual subscriber distribution before accepting dense mode. This is a plausible preventive practice for a different IP Multicast condition, specifically PIM dense-mode prune expiry. Dense mode may periodically refresh distribution and prune state, so temporary unwanted traffic can occur before pruning. In this scenario, however, the distinguishing issue is Multicast output interface list empty and the confirming observation is: The group forwarding entry contains the intended access-facing interface after receiver membership is restored.

Question 656

During a service-provider escalation, an HPE Juniper Networking engineer investigates this situation: A provider uses one unicast best-path policy for customer traffic but needs multicast source RPF lookups to follow a controlled alternative path. Which targeted check most directly distinguishes the likely cause before a configuration change?

  1. Inspect the unicast best route toward each source and the multicast packet ingress interface after the metric change.
  2. Inspect (S,G) state and the router's RP-tree-to-SPT transition settings.
  3. Inspect PIM Hello counters and interface filtering for the directly connected transit.
  4. Inspect multicast RPF table selection and the approved source routing policy.

Explanation

Correct Answer

D:

Inspect multicast RPF table selection and the approved source routing policy. This check examines the decisive condition for Multicast RPF policy separation before any unrelated changes are made. The underlying mechanism is: Multicast RPF may use explicitly controlled multicast routing information where Junos supports separate RPF lookup. The confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

Incorrect Answers

A:

Inspect the unicast best route toward each source and the multicast packet ingress interface after the metric change. This is a plausible diagnostic check for a different IP Multicast condition, specifically RPF asymmetry after IGP cost change. An IGP change can alter RPF selection, invalidating multicast arriving on an old interface even when unicast service succeeds. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

B:

Inspect (S,G) state and the router's RP-tree-to-SPT transition settings. This is a plausible diagnostic check for a different IP Multicast condition, specifically PIM shortest-path switch. PIM sparse mode can transition from shared RP tree to an efficient source-specific tree as receivers learn the source. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

C:

Inspect PIM Hello counters and interface filtering for the directly connected transit. This is a plausible diagnostic check for a different IP Multicast condition, specifically PIM hello neighbor dead. PIM neighbor discovery requires compatible Hello exchange on every required multicast-routing link. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

Question 657

During a new PE-router service turn-up, an HPE Juniper Networking engineer investigates this situation: A provider uses one unicast best-path policy for customer traffic but needs multicast source RPF lookups to follow a controlled alternative path. Which routing or service mechanism best explains the reported behavior?

  1. Multicast RPF may use explicitly controlled multicast routing information where Junos supports separate RPF lookup.
  2. An IGP change can alter RPF selection, invalidating multicast arriving on an old interface even when unicast service succeeds.
  3. PIM sparse mode can transition from shared RP tree to an efficient source-specific tree as receivers learn the source.
  4. Reverse-path forwarding rejects traffic received away from the interface selected as the path toward the multicast source.

Explanation

Correct Answer

A:

Multicast RPF may use explicitly controlled multicast routing information where Junos supports separate RPF lookup. This is the causal rule that fits the observed state, not just a correlated symptom. To distinguish it from other failures, look for: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding. The targeted correction is: Implement a supported source-specific RPF control only when justified and tested.

Incorrect Answers

B:

An IGP change can alter RPF selection, invalidating multicast arriving on an old interface even when unicast service succeeds. This is a plausible protocol explanation for a different IP Multicast condition, specifically RPF asymmetry after IGP cost change. An IGP change can alter RPF selection, invalidating multicast arriving on an old interface even when unicast service succeeds. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

C:

PIM sparse mode can transition from shared RP tree to an efficient source-specific tree as receivers learn the source. This is a plausible protocol explanation for a different IP Multicast condition, specifically PIM shortest-path switch. PIM sparse mode can transition from shared RP tree to an efficient source-specific tree as receivers learn the source. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

D:

Reverse-path forwarding rejects traffic received away from the interface selected as the path toward the multicast source. This is a plausible protocol explanation for a different IP Multicast condition, specifically PIM RPF interface mismatch. Reverse-path forwarding rejects traffic received away from the interface selected as the path toward the multicast source. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

Question 658

During a customer VPN change window, an HPE Juniper Networking engineer investigates this situation: A provider uses one unicast best-path policy for customer traffic but needs multicast source RPF lookups to follow a controlled alternative path. After the appropriate response, which observation would best confirm that the stated service condition is handled correctly?

  1. The multicast source ingress matches current RPF route selection and forwarding resumes.
  2. The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.
  3. The multicast forwarding path follows the intended source RPF route and RP detour disappears.
  4. RPF counters clear and incoming traffic on the RPF interface is forwarded to the intended receiver list.

Explanation

Correct Answer

B:

The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding. This observation directly tests the fault hypothesis rather than simply showing that a session or interface exists. The underlying reason is: Multicast RPF may use explicitly controlled multicast routing information where Junos supports separate RPF lookup.

Incorrect Answers

A:

The multicast source ingress matches current RPF route selection and forwarding resumes. This is a plausible observed evidence for a different IP Multicast condition, specifically RPF asymmetry after IGP cost change. An IGP change can alter RPF selection, invalidating multicast arriving on an old interface even when unicast service succeeds. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

C:

The multicast forwarding path follows the intended source RPF route and RP detour disappears. This is a plausible observed evidence for a different IP Multicast condition, specifically PIM shortest-path switch. PIM sparse mode can transition from shared RP tree to an efficient source-specific tree as receivers learn the source. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

D:

RPF counters clear and incoming traffic on the RPF interface is forwarded to the intended receiver list. This is a plausible observed evidence for a different IP Multicast condition, specifically PIM RPF interface mismatch. Reverse-path forwarding rejects traffic received away from the interface selected as the path toward the multicast source. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

Question 659

During a core-routing migration rehearsal, an HPE Juniper Networking engineer investigates this situation: A provider uses one unicast best-path policy for customer traffic but needs multicast source RPF lookups to follow a controlled alternative path. Which response or focused corrective action best addresses this situation without changing unrelated components?

  1. Correct multicast path placement or source RPF design to agree with the intended unicast topology.
  2. Allow supported SPT switchover for the required group and policy.
  3. Implement a supported source-specific RPF control only when justified and tested.
  4. Correct source reachability, RPF policy or topology so valid multicast traffic arrives on the selected RPF interface.

Explanation

Correct Answer

C:

Implement a supported source-specific RPF control only when justified and tested. The change addresses the root behavior described here: Multicast RPF may use explicitly controlled multicast routing information where Junos supports separate RPF lookup. Verify success with: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

Incorrect Answers

A:

Correct multicast path placement or source RPF design to agree with the intended unicast topology. This is a plausible configuration or operational fix for a different IP Multicast condition, specifically RPF asymmetry after IGP cost change. An IGP change can alter RPF selection, invalidating multicast arriving on an old interface even when unicast service succeeds. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

B:

Allow supported SPT switchover for the required group and policy. This is a plausible configuration or operational fix for a different IP Multicast condition, specifically PIM shortest-path switch. PIM sparse mode can transition from shared RP tree to an efficient source-specific tree as receivers learn the source. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

D:

Correct source reachability, RPF policy or topology so valid multicast traffic arrives on the selected RPF interface. This is a plausible configuration or operational fix for a different IP Multicast condition, specifically PIM RPF interface mismatch. Reverse-path forwarding rejects traffic received away from the interface selected as the path toward the multicast source. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

Question 660

During a backbone POP acceptance review, an HPE Juniper Networking engineer investigates this situation: A provider uses one unicast best-path policy for customer traffic but needs multicast source RPF lookups to follow a controlled alternative path. Which operational control would best prevent a recurrence of this exact failure mode?

  1. Include multicast RPF tests in every core metric migration.
  2. Validate path change effects on packet loss and multicast jitter.
  3. Include protocol control-plane permit tests in multicast transit security reviews.
  4. Audit multicast and unicast route tables independently during asymmetric routing changes.

Explanation

Correct Answer

D:

Audit multicast and unicast route tables independently during asymmetric routing changes. The control limits repetition of the described root condition: Multicast RPF may use explicitly controlled multicast routing information where Junos supports separate RPF lookup. During audits, confirm: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

Incorrect Answers

A:

Include multicast RPF tests in every core metric migration. This is a plausible preventive practice for a different IP Multicast condition, specifically RPF asymmetry after IGP cost change. An IGP change can alter RPF selection, invalidating multicast arriving on an old interface even when unicast service succeeds. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

B:

Validate path change effects on packet loss and multicast jitter. This is a plausible preventive practice for a different IP Multicast condition, specifically PIM shortest-path switch. PIM sparse mode can transition from shared RP tree to an efficient source-specific tree as receivers learn the source. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.

C:

Include protocol control-plane permit tests in multicast transit security reviews. This is a plausible preventive practice for a different IP Multicast condition, specifically PIM hello neighbor dead. PIM neighbor discovery requires compatible Hello exchange on every required multicast-routing link. In this scenario, however, the distinguishing issue is Multicast RPF policy separation and the confirming observation is: The configured RPF selection points to the intended valid upstream interface without disturbing ordinary unicast forwarding.


Service Provider Routing and Switching, Professional (JNCIP-SP) (JN0-664) Practice Tests

Purchase Individually

JN0-664 Premium File

Premium File
JN0-664 Premium File
96 Q&A
$76.99$69.99

Site Search:

 

VISA, MasterCard, AmericanExpress, UnionPay

SPECIAL OFFER: GET 10% OFF

ExamCollection Premium

ExamCollection Premium Files

Pass your Exam with ExamCollection's PREMIUM files!

  • ExamCollection Certified Safe Files
  • Guaranteed to have ACTUAL Exam Questions
  • Up-to-Date Exam Study Material - Verified by Experts
  • Instant Downloads
Enter Your Email Address to Receive Your 10% Off Discount Code
A Confirmation Link will be sent to this email address to verify your login
We value your privacy. We will not rent or sell your email address

SPECIAL OFFER: GET 10% OFF

Use Discount Code:

MIN10OFF

A confirmation link was sent to your e-mail.
Please check your mailbox for a message from support@examcollection.com and follow the directions.

Next

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.