Question 880
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: An internal HDD is absent from firmware after a PC is moved, but the technician finds its SATA power cable disconnected. A portable disk repeatedly disconnects only when attached through a loose external USB cable while its health data looks normal. What is the most appropriate plan for this situation?
- Restore the correct SATA power connection and recheck drive detection; verify data protection and plan proactive disk replacement rather than ignore the health trend.
- Stop unnecessary writes, protect recoverable data and replace the failing drive after safe backup or recovery; verify data protection and plan proactive disk replacement rather than ignore the health trend.
- Restore the correct SATA power connection and recheck drive detection; replace the suspect cable or connector and confirm stable operation before condemning the drive.
- Stop unnecessary writes, protect recoverable data and replace the failing drive after safe backup or recovery; replace the suspect cable or connector and confirm stable operation before condemning the drive.
Explanation
Correct Answer
C:For ticket (1), A storage device without electrical power cannot enumerate even with a healthy data cable. For ticket (2), Transport errors from intermittent cabling can imitate storage failure.
Incorrect Answers
A:For ticket 2, replace the suspect cable or connector and confirm stable operation before condemning the drive. Transport errors from intermittent cabling can imitate storage failure.
B:For ticket 1, restore the correct SATA power connection and recheck drive detection. A storage device without electrical power cannot enumerate even with a healthy data cable. For ticket 2, replace the suspect cable or connector and confirm stable operation before condemning the drive. Transport errors from intermittent cabling can imitate storage failure.
D:For ticket 1, restore the correct SATA power connection and recheck drive detection. A storage device without electrical power cannot enumerate even with a healthy data cable.
Question 881
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: A spinning hard drive reports growing SMART reallocated sectors and increasing uncorrectable errors across successive checks. A portable disk repeatedly disconnects only when attached through a loose external USB cable while its health data looks normal. Which course of action addresses the stated issues?
- Verify data protection and plan proactive disk replacement rather than ignore the health trend; restore the correct SATA power connection and recheck drive detection.
- Stop unnecessary writes, protect recoverable data and replace the failing drive after safe backup or recovery; restore the correct SATA power connection and recheck drive detection.
- Verify data protection and plan proactive disk replacement rather than ignore the health trend; replace the suspect cable or connector and confirm stable operation before condemning the drive.
- Stop unnecessary writes, protect recoverable data and replace the failing drive after safe backup or recovery; replace the suspect cable or connector and confirm stable operation before condemning the drive.
Explanation
Correct Answer
C:For ticket (1), Increasing media errors can indicate degradation before complete drive failure. For ticket (2), Transport errors from intermittent cabling can imitate storage failure.
Incorrect Answers
A:For ticket 2, replace the suspect cable or connector and confirm stable operation before condemning the drive. Transport errors from intermittent cabling can imitate storage failure.
B:For ticket 1, verify data protection and plan proactive disk replacement rather than ignore the health trend. Increasing media errors can indicate degradation before complete drive failure. For ticket 2, replace the suspect cable or connector and confirm stable operation before condemning the drive. Transport errors from intermittent cabling can imitate storage failure.
D:For ticket 1, verify data protection and plan proactive disk replacement rather than ignore the health trend. Increasing media errors can indicate degradation before complete drive failure.
Question 882
A service coordinator has THREE separate support tickets and needs the correct matching actions: A desktop hard drive emits repeating clicking sounds and files become intermittently unreadable during ordinary access. An internal HDD is absent from firmware after a PC is moved, but the technician finds its SATA power cable disconnected. A spinning hard drive reports growing SMART reallocated sectors and increasing uncorrectable errors across successive checks. Which response best addresses these needs?
- Stop unnecessary writes, protect recoverable data and replace the failing drive after safe backup or recovery; replace the suspect cable or connector and confirm stable operation before condemning the drive; and verify data protection and plan proactive disk replacement rather than ignore the health trend.
- Stop unnecessary writes, protect recoverable data and replace the failing drive after safe backup or recovery; restore the correct SATA power connection and recheck drive detection; and replace the suspect cable or connector and confirm stable operation before condemning the drive.
- Stop unnecessary writes, protect recoverable data and replace the failing drive after safe backup or recovery; restore the correct SATA power connection and recheck drive detection; and verify data protection and plan proactive disk replacement rather than ignore the health trend.
- Replace the suspect cable or connector and confirm stable operation before condemning the drive; restore the correct SATA power connection and recheck drive detection; and verify data protection and plan proactive disk replacement rather than ignore the health trend.
Explanation
Correct Answer
C:For ticket (1), Repeated mechanical clicks and read errors are warning signs of possible head or media failure. For ticket (2), A storage device without electrical power cannot enumerate even with a healthy data cable. For ticket (3), Increasing media errors can indicate degradation before complete drive failure.
Incorrect Answers
A:For ticket 2, restore the correct SATA power connection and recheck drive detection. A storage device without electrical power cannot enumerate even with a healthy data cable.
B:For ticket 3, verify data protection and plan proactive disk replacement rather than ignore the health trend. Increasing media errors can indicate degradation before complete drive failure.
D:For ticket 1, stop unnecessary writes, protect recoverable data and replace the failing drive after safe backup or recovery. Repeated mechanical clicks and read errors are warning signs of possible head or media failure.
Question 883
An IT support worker is asked to resolve this case: A laptop screen works normally but an HDMI projector shows no image because Windows is configured to use only the built-in display. Which next step MOST directly resolves the reported condition?
- Choose a supported display resolution or a converter meeting the required mode.
- Restore the intended display rotation and projector geometry settings.
- Select the correct duplicate or extend display mode and confirm projector input selection.
- Change the monitor to the active HDMI input before changing GPU hardware.
Explanation
Correct Answer
C:Output routing settings can leave an otherwise functioning external display blank.
Incorrect Answers
A:Active video converters can impose additional resolution and refresh limits; output routing settings can leave an otherwise functioning external display blank.
B:Output orientation is a software/display configuration issue rather than proof of panel damage; output routing settings can leave an otherwise functioning external display blank.
D:A monitor can have valid power but display nothing when listening on the wrong input; output routing settings can leave an otherwise functioning external display blank.
Question 884
A service bench observes this hardware or network symptom: A second monitor remains black while the first works, and the new monitor's input is set to DisplayPort despite an HDMI cable being used. What should the support specialist recommend FIRST within the stated limits?
- Select the correct duplicate or extend display mode and confirm projector input selection.
- Change the monitor to the active HDMI input before changing GPU hardware.
- Choose a supported display resolution or a converter meeting the required mode.
- Restore the intended display rotation and projector geometry settings.
Explanation
Correct Answer
B:A monitor can have valid power but display nothing when listening on the wrong input.
Incorrect Answers
A:Selecting the correct duplicate or extend display mode and confirming projector input selection would not change the monitor to the active HDMI input.
C:Choosing a supported display resolution or a converter meeting the required mode would not change the monitor to the active HDMI input.
D:Restoring the intended display rotation and projector geometry settings would not change the monitor to the active HDMI input.
Question 885
During a controlled office IT maintenance window, the technician notes: A workstation uses an analog VGA converter that supports only 1080p while the user sets a higher mode unsupported by the adapter. What is the MOST appropriate technician action?
- Choose a supported display resolution or a converter meeting the required mode.
- Restore the intended display rotation and projector geometry settings.
- Select the correct duplicate or extend display mode and confirm projector input selection.
- Change the monitor to the active HDMI input before changing GPU hardware.
Explanation
Correct Answer
A:Active video converters can impose additional resolution and refresh limits.
Incorrect Answers
B:Output orientation is a software/display configuration issue rather than proof of panel damage; active video converters can impose additional resolution and refresh limits.
C:Output routing settings can leave an otherwise functioning external display blank; active video converters can impose additional resolution and refresh limits.
D:A monitor can have valid power but display nothing when listening on the wrong input; active video converters can impose additional resolution and refresh limits.
Question 886
A support case documents the following situation: A conference-room projector displays an image rotated sideways after someone changed the graphics orientation setting. Which response BEST addresses the actual cause or requirement?
- Change the monitor to the active HDMI input before changing GPU hardware.
- Choose a supported display resolution or a converter meeting the required mode.
- Restore the intended display rotation and projector geometry settings.
- Select the correct duplicate or extend display mode and confirm projector input selection.
Explanation
Correct Answer
C:Output orientation is a software/display configuration issue rather than proof of panel damage.
Incorrect Answers
A:Changing the monitor to the active HDMI input would not restore the intended display rotation and projector geometry settings.
B:Choosing a supported display resolution or a converter meeting the required mode would not restore the intended display rotation and projector geometry settings.
D:Selecting the correct duplicate or extend display mode and confirming projector input selection would not restore the intended display rotation and projector geometry settings.
Question 887
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: A laptop screen works normally but an HDMI projector shows no image because Windows is configured to use only the built-in display. A second monitor remains black while the first works, and the new monitor's input is set to DisplayPort despite an HDMI cable being used. Which course of action addresses the stated issues?
- Select the correct duplicate or extend display mode and confirm projector input selection; restore the intended display rotation and projector geometry settings.
- Choose a supported display resolution or a converter meeting the required mode; restore the intended display rotation and projector geometry settings.
- Select the correct duplicate or extend display mode and confirm projector input selection; Change the monitor to the active HDMI input before changing GPU hardware.
- Choose a supported display resolution or a converter meeting the required mode; Change the monitor to the active HDMI input before changing GPU hardware.
Explanation
Correct Answer
C:For ticket (1), Output routing settings can leave an otherwise functioning external display blank. For ticket (2), A monitor can have valid power but display nothing when listening on the wrong input.
Incorrect Answers
A:For ticket 2, change the monitor to the active HDMI input before changing GPU hardware. A monitor can have valid power but display nothing when listening on the wrong input.
B:For ticket 1, select the correct duplicate or extend display mode and confirm projector input selection. Output routing settings can leave an otherwise functioning external display blank. For ticket 2, change the monitor to the active HDMI input before changing GPU hardware. A monitor can have valid power but display nothing when listening on the wrong input.
D:For ticket 1, select the correct duplicate or extend display mode and confirm projector input selection. Output routing settings can leave an otherwise functioning external display blank.
Question 888
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: A laptop screen works normally but an HDMI projector shows no image because Windows is configured to use only the built-in display. A workstation uses an analog VGA converter that supports only 1080p while the user sets a higher mode unsupported by the adapter. Which response best addresses these needs?
- Select the correct duplicate or extend display mode and confirm projector input selection; choose a supported display resolution or a converter meeting the required mode.
- Change the monitor to the active HDMI input before changing GPU hardware; choose a supported display resolution or a converter meeting the required mode.
- Select the correct duplicate or extend display mode and confirm projector input selection; restore the intended display rotation and projector geometry settings.
- Change the monitor to the active HDMI input before changing GPU hardware; restore the intended display rotation and projector geometry settings.
Explanation
Correct Answer
A:For ticket (1), Output routing settings can leave an otherwise functioning external display blank. For ticket (2), Active video converters can impose additional resolution and refresh limits.
Incorrect Answers
B:For ticket 1, select the correct duplicate or extend display mode and confirm projector input selection. Output routing settings can leave an otherwise functioning external display blank.
C:For ticket 2, choose a supported display resolution or a converter meeting the required mode. Active video converters can impose additional resolution and refresh limits.
D:For ticket 1, select the correct duplicate or extend display mode and confirm projector input selection. Output routing settings can leave an otherwise functioning external display blank. For ticket 2, choose a supported display resolution or a converter meeting the required mode. Active video converters can impose additional resolution and refresh limits.
Question 889
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: A second monitor remains black while the first works, and the new monitor's input is set to DisplayPort despite an HDMI cable being used. A conference-room projector displays an image rotated sideways after someone changed the graphics orientation setting. What is the most appropriate plan for this situation?
- Change the monitor to the active HDMI input before changing GPU hardware; restore the intended display rotation and projector geometry settings.
- Select the correct duplicate or extend display mode and confirm projector input selection; restore the intended display rotation and projector geometry settings.
- Change the monitor to the active HDMI input before changing GPU hardware; choose a supported display resolution or a converter meeting the required mode.
- Select the correct duplicate or extend display mode and confirm projector input selection; choose a supported display resolution or a converter meeting the required mode.
Explanation
Correct Answer
A:For ticket (1), A monitor can have valid power but display nothing when listening on the wrong input. For ticket (2), Output orientation is a software/display configuration issue rather than proof of panel damage.
Incorrect Answers
B:For ticket 1, change the monitor to the active HDMI input before changing GPU hardware. A monitor can have valid power but display nothing when listening on the wrong input.
C:For ticket 2, restore the intended display rotation and projector geometry settings. Output orientation is a software/display configuration issue rather than proof of panel damage.
D:For ticket 1, change the monitor to the active HDMI input before changing GPU hardware. A monitor can have valid power but display nothing when listening on the wrong input. For ticket 2, restore the intended display rotation and projector geometry settings. Output orientation is a software/display configuration issue rather than proof of panel damage.
Question 890
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: A workstation uses an analog VGA converter that supports only 1080p while the user sets a higher mode unsupported by the adapter. A conference-room projector displays an image rotated sideways after someone changed the graphics orientation setting. Which course of action addresses the stated issues?
- Choose a supported display resolution or a converter meeting the required mode; Change the monitor to the active HDMI input before changing GPU hardware.
- Select the correct duplicate or extend display mode and confirm projector input selection; Change the monitor to the active HDMI input before changing GPU hardware.
- Choose a supported display resolution or a converter meeting the required mode; restore the intended display rotation and projector geometry settings.
- Select the correct duplicate or extend display mode and confirm projector input selection; restore the intended display rotation and projector geometry settings.
Explanation
Correct Answer
C:For ticket (1), Active video converters can impose additional resolution and refresh limits. For ticket (2), Output orientation is a software/display configuration issue rather than proof of panel damage.
Incorrect Answers
A:For ticket 2, restore the intended display rotation and projector geometry settings. Output orientation is a software/display configuration issue rather than proof of panel damage.
B:For ticket 1, choose a supported display resolution or a converter meeting the required mode. Active video converters can impose additional resolution and refresh limits. For ticket 2, restore the intended display rotation and projector geometry settings. Output orientation is a software/display configuration issue rather than proof of panel damage.
D:For ticket 1, choose a supported display resolution or a converter meeting the required mode. Active video converters can impose additional resolution and refresh limits.
CompTIA A+ Certification Exam: Core 1 (220-1201) Practice Tests