Pass Your Juniper JN0-664 Exam Easy!

Juniper JN0-664 Exam Questions & Answers, Accurate & Verified By IT Experts

Instant Download, Free Fast Updates, 99.6% Pass Rate

JN0-664 Premium VCE File

Juniper JN0-664 Premium File

96 Questions & Answers

Last Update: Oct 12, 2026

$69.99

JN0-664 Bundle gives you unlimited access to "JN0-664" files. However, this does not replace the need for a .vce exam simulator. To download VCE exam simulator click here
JN0-664 Premium VCE File
Juniper JN0-664 Premium File

96 Questions & Answers

Last Update: Oct 12, 2026

$69.99

Juniper JN0-664 Exam Bundle gives you unlimited access to "JN0-664" files. However, this does not replace the need for a .vce exam simulator. To download your .vce exam simulator click here

Juniper JN0-664 Practice Test 91

Question 900

During a backbone POP acceptance review, an HPE Juniper Networking engineer investigates this situation: A customer bridges two sites through parallel VPLS paths and the same MAC address oscillates rapidly between remote attachments. Which operational control would best prevent a recurrence of this exact failure mode?

  1. Alert on oscillating MAC addresses that exceed planned mobility behavior.
  2. Maintain a per-VPN site-ID allocation register.
  3. Maintain a site-VLAN-to-EVI mapping table and test isolation after adding services.
  4. Alert on rapid MAC moves and validate redundant CPE topology.

Explanation

Correct Answer

D:

Alert on rapid MAC moves and validate redundant CPE topology. The control limits repetition of the described root condition: Multipoint Layer 2 forwarding can become unstable when the same source MAC appears alternately from multiple ports or pseudowires. During audits, confirm: The customer MAC learns on the expected attachment without repeated moves after loop removal.

Incorrect Answers

A:

Alert on oscillating MAC addresses that exceed planned mobility behavior. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically EVPN duplicate MAC protection. Repeated conflicting MAC advertisements can indicate duplicate endpoint identity rather than valid sequential migration. In this scenario, however, the distinguishing issue is VPLS MAC move instability and the confirming observation is: The customer MAC learns on the expected attachment without repeated moves after loop removal.

B:

Maintain a per-VPN site-ID allocation register. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically BGP L2VPN site ID collision. BGP L2VPN site identifiers help map distinct site attachments into the signaled service topology. In this scenario, however, the distinguishing issue is VPLS MAC move instability and the confirming observation is: The customer MAC learns on the expected attachment without repeated moves after loop removal.

C:

Maintain a site-VLAN-to-EVI mapping table and test isolation after adding services. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically VLAN normalization mismatch. EVPN can separate local VLAN identifiers from a shared service identity when correct translation and normalization are configured. In this scenario, however, the distinguishing issue is VPLS MAC move instability and the confirming observation is: The customer MAC learns on the expected attachment without repeated moves after loop removal.

Question 901

During an edge-to-core validation, an HPE Juniper Networking engineer investigates this situation: An operator creates a new VPLS pseudowire and multicast frames start circulating between remote PEs because forwarding rules allow remote PW-to-remote PW loops. Which targeted check most directly distinguishes the likely cause before a configuration change?

  1. Inspect split-horizon forwarding treatment for traffic received from VPLS pseudowires.
  2. Compare ingress VLAN unit counters and the specific L2VPN instance's attachment configuration.
  3. Inspect outer transport label reachability and remote PE next-hop resolution independent of the VC label.
  4. Inspect EVPN type 3 inclusive multicast route exchange and associated flooding membership.

Explanation

Correct Answer

A:

Inspect split-horizon forwarding treatment for traffic received from VPLS pseudowires. This check examines the decisive condition for VPLS split-horizon protection before any unrelated changes are made. The underlying mechanism is: VPLS needs loop-prevention controls such as split-horizon behavior when forwarding between remote pseudowires. The confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

Incorrect Answers

B:

Compare ingress VLAN unit counters and the specific L2VPN instance's attachment configuration. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically L2VPN attachment interface wrong unit. A signaled pseudowire only carries CE frames that enter its actual local attachment circuit. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

C:

Inspect outer transport label reachability and remote PE next-hop resolution independent of the VC label. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically Pseudowire transport unreachable. Pseudowire service labels identify the circuit, while a separate MPLS transport path carries the traffic to the remote PE. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

D:

Inspect EVPN type 3 inclusive multicast route exchange and associated flooding membership. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically EVPN inclusive multicast route. EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

Question 902

During a high-availability validation, an HPE Juniper Networking engineer investigates this situation: An operator creates a new VPLS pseudowire and multicast frames start circulating between remote PEs because forwarding rules allow remote PW-to-remote PW loops. Which routing or service mechanism best explains the reported behavior?

  1. A signaled pseudowire only carries CE frames that enter its actual local attachment circuit.
  2. VPLS needs loop-prevention controls such as split-horizon behavior when forwarding between remote pseudowires.
  3. Pseudowire service labels identify the circuit, while a separate MPLS transport path carries the traffic to the remote PE.
  4. EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI.

Explanation

Correct Answer

B:

VPLS needs loop-prevention controls such as split-horizon behavior when forwarding between remote pseudowires. This is the causal rule that fits the observed state, not just a correlated symptom. To distinguish it from other failures, look for: Test frames cross the intended CE attachments once without repeated amplification. The targeted correction is: Restore the supported VPLS split-horizon or equivalent loop-free topology behavior.

Incorrect Answers

A:

A signaled pseudowire only carries CE frames that enter its actual local attachment circuit. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically L2VPN attachment interface wrong unit. A signaled pseudowire only carries CE frames that enter its actual local attachment circuit. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

C:

Pseudowire service labels identify the circuit, while a separate MPLS transport path carries the traffic to the remote PE. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically Pseudowire transport unreachable. Pseudowire service labels identify the circuit, while a separate MPLS transport path carries the traffic to the remote PE. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

D:

EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically EVPN inclusive multicast route. EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

Question 903

During a Junos routing maintenance review, an HPE Juniper Networking engineer investigates this situation: An operator creates a new VPLS pseudowire and multicast frames start circulating between remote PEs because forwarding rules allow remote PW-to-remote PW loops. After the appropriate response, which observation would best confirm that the stated service condition is handled correctly?

  1. Packet counters on the intended unit and pseudowire both increase for a test frame.
  2. Label switching to the far PE is operational and the service frames are delivered over the signaled circuit.
  3. Test frames cross the intended CE attachments once without repeated amplification.
  4. Each authorized PE appears in the replication set and controlled BUM test traffic reaches the intended sites.

Explanation

Correct Answer

C:

Test frames cross the intended CE attachments once without repeated amplification. This observation directly tests the fault hypothesis rather than simply showing that a session or interface exists. The underlying reason is: VPLS needs loop-prevention controls such as split-horizon behavior when forwarding between remote pseudowires.

Incorrect Answers

A:

Packet counters on the intended unit and pseudowire both increase for a test frame. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically L2VPN attachment interface wrong unit. A signaled pseudowire only carries CE frames that enter its actual local attachment circuit. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

B:

Label switching to the far PE is operational and the service frames are delivered over the signaled circuit. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically Pseudowire transport unreachable. Pseudowire service labels identify the circuit, while a separate MPLS transport path carries the traffic to the remote PE. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

D:

Each authorized PE appears in the replication set and controlled BUM test traffic reaches the intended sites. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically EVPN inclusive multicast route. EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

Question 904

During a multisite network cutover, an HPE Juniper Networking engineer investigates this situation: An operator creates a new VPLS pseudowire and multicast frames start circulating between remote PEs because forwarding rules allow remote PW-to-remote PW loops. Which response or focused corrective action best addresses this situation without changing unrelated components?

  1. Bind the correct VLAN logical unit or service interface to the L2VPN instance.
  2. Restore the underlying MPLS transport without resetting a healthy service-label agreement.
  3. Restore correct type 3 advertisement and service membership signaling.
  4. Restore the supported VPLS split-horizon or equivalent loop-free topology behavior.

Explanation

Correct Answer

D:

Restore the supported VPLS split-horizon or equivalent loop-free topology behavior. The change addresses the root behavior described here: VPLS needs loop-prevention controls such as split-horizon behavior when forwarding between remote pseudowires. Verify success with: Test frames cross the intended CE attachments once without repeated amplification.

Incorrect Answers

A:

Bind the correct VLAN logical unit or service interface to the L2VPN instance. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically L2VPN attachment interface wrong unit. A signaled pseudowire only carries CE frames that enter its actual local attachment circuit. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

B:

Restore the underlying MPLS transport without resetting a healthy service-label agreement. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically Pseudowire transport unreachable. Pseudowire service labels identify the circuit, while a separate MPLS transport path carries the traffic to the remote PE. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

C:

Restore correct type 3 advertisement and service membership signaling. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically EVPN inclusive multicast route. EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

Question 905

During a metro aggregation incident, an HPE Juniper Networking engineer investigates this situation: An operator creates a new VPLS pseudowire and multicast frames start circulating between remote PEs because forwarding rules allow remote PW-to-remote PW loops. Which operational control would best prevent a recurrence of this exact failure mode?

  1. Test broadcast storm containment before admitting additional VPLS PEs.
  2. Cross-check physical port, VLAN tag and logical unit against customer acceptance drawings.
  3. Require both service label and transport label checks before declaring a pseudowire active.
  4. Test BUM delivery separately from known-unicast MAC reachability.

Explanation

Correct Answer

A:

Test broadcast storm containment before admitting additional VPLS PEs. The control limits repetition of the described root condition: VPLS needs loop-prevention controls such as split-horizon behavior when forwarding between remote pseudowires. During audits, confirm: Test frames cross the intended CE attachments once without repeated amplification.

Incorrect Answers

B:

Cross-check physical port, VLAN tag and logical unit against customer acceptance drawings. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically L2VPN attachment interface wrong unit. A signaled pseudowire only carries CE frames that enter its actual local attachment circuit. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

C:

Require both service label and transport label checks before declaring a pseudowire active. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically Pseudowire transport unreachable. Pseudowire service labels identify the circuit, while a separate MPLS transport path carries the traffic to the remote PE. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

D:

Test BUM delivery separately from known-unicast MAC reachability. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically EVPN inclusive multicast route. EVPN type 3 advertisements can establish participants in broadcast, unknown-unicast and multicast replication for an EVI. In this scenario, however, the distinguishing issue is VPLS split-horizon protection and the confirming observation is: Test frames cross the intended CE attachments once without repeated amplification.

Question 906

During an inter-POP failover test, an HPE Juniper Networking engineer investigates this situation: A network team expects dynamic site discovery from a manually provisioned LDP VPLS service and cannot explain why new PEs are not automatically participating. Which targeted check most directly distinguishes the likely cause before a configuration change?

  1. Inspect local and remote site IDs and the BGP L2VPN route connection mapping.
  2. Inspect whether VPLS uses BGP autodiscovery/signaling or explicit LDP neighbor configuration.
  3. Inspect VPLS route targets and the set of learned remote participants.
  4. Inspect EVPN BGP next-hop resolution and the MPLS transport or VXLAN encapsulation path in use.

Explanation

Correct Answer

B:

Inspect whether VPLS uses BGP autodiscovery/signaling or explicit LDP neighbor configuration. This check examines the decisive condition for VPLS BGP versus LDP signaling before any unrelated changes are made. The underlying mechanism is: VPLS signaling design determines how remote sites are discovered and how service labels are exchanged. The confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

Incorrect Answers

A:

Inspect local and remote site IDs and the BGP L2VPN route connection mapping. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically BGP L2VPN site ID collision. BGP L2VPN site identifiers help map distinct site attachments into the signaled service topology. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

C:

Inspect VPLS route targets and the set of learned remote participants. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically VPLS route target site leakage. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

D:

Inspect EVPN BGP next-hop resolution and the MPLS transport or VXLAN encapsulation path in use. This is a plausible diagnostic check for a different Layer 2 VPNs condition, specifically EVPN core route resolution. EVPN control-plane MAC information needs an independently working transport data plane to deliver frames. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

Question 907

During a control-plane reliability review, an HPE Juniper Networking engineer investigates this situation: A network team expects dynamic site discovery from a manually provisioned LDP VPLS service and cannot explain why new PEs are not automatically participating. Which routing or service mechanism best explains the reported behavior?

  1. BGP L2VPN site identifiers help map distinct site attachments into the signaled service topology.
  2. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused.
  3. VPLS signaling design determines how remote sites are discovered and how service labels are exchanged.
  4. VPLS provides multipoint Ethernet bridging, so traffic to unknown MAC addresses can be flooded within the VPN forwarding domain.

Explanation

Correct Answer

C:

VPLS signaling design determines how remote sites are discovered and how service labels are exchanged. This is the causal rule that fits the observed state, not just a correlated symptom. To distinguish it from other failures, look for: The new PE participates after the correct signaling and neighbor configuration is completed. The targeted correction is: Use the chosen BGP or LDP signaling model consistently rather than mixing assumptions.

Incorrect Answers

A:

BGP L2VPN site identifiers help map distinct site attachments into the signaled service topology. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically BGP L2VPN site ID collision. BGP L2VPN site identifiers help map distinct site attachments into the signaled service topology. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

B:

BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically VPLS route target site leakage. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

D:

VPLS provides multipoint Ethernet bridging, so traffic to unknown MAC addresses can be flooded within the VPN forwarding domain. This is a plausible protocol explanation for a different Layer 2 VPNs condition, specifically VPLS flooding unknown unicast. VPLS provides multipoint Ethernet bridging, so traffic to unknown MAC addresses can be flooded within the VPN forwarding domain. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

Question 908

During a service-provider escalation, an HPE Juniper Networking engineer investigates this situation: A network team expects dynamic site discovery from a manually provisioned LDP VPLS service and cannot explain why new PEs are not automatically participating. After the appropriate response, which observation would best confirm that the stated service condition is handled correctly?

  1. Each site advertises its planned unique identity and the remote connection mapping is unambiguous.
  2. Unrelated remote sites disappear from the VPN membership and their MACs are no longer learned.
  3. MAC learning stabilizes and flooding reduces while known unicast frames target the correct remote site.
  4. The new PE participates after the correct signaling and neighbor configuration is completed.

Explanation

Correct Answer

D:

The new PE participates after the correct signaling and neighbor configuration is completed. This observation directly tests the fault hypothesis rather than simply showing that a session or interface exists. The underlying reason is: VPLS signaling design determines how remote sites are discovered and how service labels are exchanged.

Incorrect Answers

A:

Each site advertises its planned unique identity and the remote connection mapping is unambiguous. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically BGP L2VPN site ID collision. BGP L2VPN site identifiers help map distinct site attachments into the signaled service topology. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

B:

Unrelated remote sites disappear from the VPN membership and their MACs are no longer learned. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically VPLS route target site leakage. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

C:

MAC learning stabilizes and flooding reduces while known unicast frames target the correct remote site. This is a plausible observed evidence for a different Layer 2 VPNs condition, specifically VPLS flooding unknown unicast. VPLS provides multipoint Ethernet bridging, so traffic to unknown MAC addresses can be flooded within the VPN forwarding domain. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

Question 909

During a new PE-router service turn-up, an HPE Juniper Networking engineer investigates this situation: A network team expects dynamic site discovery from a manually provisioned LDP VPLS service and cannot explain why new PEs are not automatically participating. Which response or focused corrective action best addresses this situation without changing unrelated components?

  1. Use the chosen BGP or LDP signaling model consistently rather than mixing assumptions.
  2. Assign unique service site IDs and align site ranges according to the intended topology.
  3. Correct per-tenant route target assignment and BGP import policy.
  4. Fix MAC learning or excessive churn rather than disabling legitimate service discovery broadly.

Explanation

Correct Answer

A:

Use the chosen BGP or LDP signaling model consistently rather than mixing assumptions. The change addresses the root behavior described here: VPLS signaling design determines how remote sites are discovered and how service labels are exchanged. Verify success with: The new PE participates after the correct signaling and neighbor configuration is completed.

Incorrect Answers

B:

Assign unique service site IDs and align site ranges according to the intended topology. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically BGP L2VPN site ID collision. BGP L2VPN site identifiers help map distinct site attachments into the signaled service topology. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

C:

Correct per-tenant route target assignment and BGP import policy. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically VPLS route target site leakage. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

D:

Fix MAC learning or excessive churn rather than disabling legitimate service discovery broadly. This is a plausible configuration or operational fix for a different Layer 2 VPNs condition, specifically VPLS flooding unknown unicast. VPLS provides multipoint Ethernet bridging, so traffic to unknown MAC addresses can be flooded within the VPN forwarding domain. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

Question 910

During a customer VPN change window, an HPE Juniper Networking engineer investigates this situation: A network team expects dynamic site discovery from a manually provisioned LDP VPLS service and cannot explain why new PEs are not automatically participating. Which operational control would best prevent a recurrence of this exact failure mode?

  1. Maintain a per-VPN site-ID allocation register.
  2. Keep service signaling type and required peers in the provisioning contract.
  3. Perform negative remote-site membership checks before accepting a VPLS service.
  4. Use positive and negative RT import tests for each new Layer 2 VPN tenant.

Explanation

Correct Answer

B:

Keep service signaling type and required peers in the provisioning contract. The control limits repetition of the described root condition: VPLS signaling design determines how remote sites are discovered and how service labels are exchanged. During audits, confirm: The new PE participates after the correct signaling and neighbor configuration is completed.

Incorrect Answers

A:

Maintain a per-VPN site-ID allocation register. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically BGP L2VPN site ID collision. BGP L2VPN site identifiers help map distinct site attachments into the signaled service topology. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

C:

Perform negative remote-site membership checks before accepting a VPLS service. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically VPLS route target site leakage. BGP VPLS RT import membership can join unrelated sites into one Layer 2 broadcast domain if values are reused. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.

D:

Use positive and negative RT import tests for each new Layer 2 VPN tenant. This is a plausible preventive practice for a different Layer 2 VPNs condition, specifically BGP L2VPN route target mismatch. Route targets control membership and distribution of BGP-based L2VPN service advertisements. In this scenario, however, the distinguishing issue is VPLS BGP versus LDP signaling and the confirming observation is: The new PE participates after the correct signaling and neighbor configuration is completed.


Service Provider Routing and Switching, Professional (JNCIP-SP) (JN0-664) Practice Tests

Purchase Individually

JN0-664 Premium File

Premium File
JN0-664 Premium File
96 Q&A
$76.99$69.99

Site Search:

 

VISA, MasterCard, AmericanExpress, UnionPay

SPECIAL OFFER: GET 10% OFF

ExamCollection Premium

ExamCollection Premium Files

Pass your Exam with ExamCollection's PREMIUM files!

  • ExamCollection Certified Safe Files
  • Guaranteed to have ACTUAL Exam Questions
  • Up-to-Date Exam Study Material - Verified by Experts
  • Instant Downloads
Enter Your Email Address to Receive Your 10% Off Discount Code
A Confirmation Link will be sent to this email address to verify your login
We value your privacy. We will not rent or sell your email address

SPECIAL OFFER: GET 10% OFF

Use Discount Code:

MIN10OFF

A confirmation link was sent to your e-mail.
Please check your mailbox for a message from support@examcollection.com and follow the directions.

Next

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.