Question 120
An end user reports the following condition: A workstation's boot disk appears in BIOS but the OS loader fails after an unexpected power loss. What should the support specialist recommend FIRST within the stated limits?
- Restore the documented boot mode and correct boot entry before reinstalling the OS.
- Replace or reseat the SATA data cable and verify the controller port.
- Use approved startup-repair and backup recovery procedures after confirming drive health.
- Install an SSD supported by the laptop M.2 connector and firmware.
Explanation
Correct Answer
C:A corrupted boot loader can stop startup even when firmware detects the physical disk.
Incorrect Answers
A:Firmware boot configuration must match the disk's installed boot environment; a corrupted boot loader can stop startup even when firmware detects the physical disk.
B:Powering a drive does not ensure the host has a functioning data channel; a corrupted boot loader can stop startup even when firmware detects the physical disk.
D:Different M.2 modules may be physically or electrically incompatible despite similar packaging; a corrupted boot loader can stop startup even when firmware detects the physical disk.
Question 121
A help desk receives a support ticket with this evidence: A laptop with a replaced NVMe drive cannot find it because the new module uses an unsupported keying/protocol combination. What is the MOST appropriate technician action?
- Restore the documented boot mode and correct boot entry before reinstalling the OS.
- Replace or reseat the SATA data cable and verify the controller port.
- Use approved startup-repair and backup recovery procedures after confirming drive health.
- Install an SSD supported by the laptop M.2 connector and firmware.
Explanation
Correct Answer
D:Different M.2 modules may be physically or electrically incompatible despite similar packaging.
Incorrect Answers
A:Restoring the documented boot mode and correcting boot entry would not install an SSD supported by the laptop M.2 connector and firmware.
B:Replacing or reseat the SATA data cable and verifying the controller port would not install an SSD supported by the laptop M.2 connector and firmware.
C:Using approved startup-repair and backup recovery procedures after confirming drive health would not install an SSD supported by the laptop M.2 connector and firmware.
Question 122
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: A PC reports no bootable device after a technician changes the UEFI boot mode from the original configuration. A new SATA drive is invisible in firmware because the technician used a defective data lead while power is present. Which course of action addresses the stated issues?
- Restore the documented boot mode and correct boot entry before reinstalling the OS; replace or reseat the SATA data cable and verify the controller port.
- Use approved startup-repair and backup recovery procedures after confirming drive health; replace or reseat the SATA data cable and verify the controller port.
- Restore the documented boot mode and correct boot entry before reinstalling the OS; install an SSD supported by the laptop M.2 connector and firmware.
- Use approved startup-repair and backup recovery procedures after confirming drive health; install an SSD supported by the laptop M.2 connector and firmware.
Explanation
Correct Answer
A:For ticket (1), Firmware boot configuration must match the disk's installed boot environment. For ticket (2), Powering a drive does not ensure the host has a functioning data channel.
Incorrect Answers
B:For ticket 1, restore the documented boot mode and correct boot entry before reinstalling the OS. Firmware boot configuration must match the disk's installed boot environment.
C:For ticket 2, replace or reseat the SATA data cable and verify the controller port. Powering a drive does not ensure the host has a functioning data channel.
D:For ticket 1, restore the documented boot mode and correct boot entry before reinstalling the OS. Firmware boot configuration must match the disk's installed boot environment. For ticket 2, replace or reseat the SATA data cable and verify the controller port. Powering a drive does not ensure the host has a functioning data channel.
Question 123
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: A PC reports no bootable device after a technician changes the UEFI boot mode from the original configuration. A workstation's boot disk appears in BIOS but the OS loader fails after an unexpected power loss. Which response best addresses these needs?
- Replace or reseat the SATA data cable and verify the controller port; use approved startup-repair and backup recovery procedures after confirming drive health.
- Restore the documented boot mode and correct boot entry before reinstalling the OS; install an SSD supported by the laptop M.2 connector and firmware.
- Replace or reseat the SATA data cable and verify the controller port; install an SSD supported by the laptop M.2 connector and firmware.
- Restore the documented boot mode and correct boot entry before reinstalling the OS; use approved startup-repair and backup recovery procedures after confirming drive health.
Explanation
Correct Answer
D:For ticket (1), Firmware boot configuration must match the disk's installed boot environment. For ticket (2), A corrupted boot loader can stop startup even when firmware detects the physical disk.
Incorrect Answers
A:For ticket 1, restore the documented boot mode and correct boot entry before reinstalling the OS. Firmware boot configuration must match the disk's installed boot environment.
B:For ticket 2, use approved startup-repair and backup recovery procedures after confirming drive health. A corrupted boot loader can stop startup even when firmware detects the physical disk.
C:For ticket 1, restore the documented boot mode and correct boot entry before reinstalling the OS. Firmware boot configuration must match the disk's installed boot environment. For ticket 2, use approved startup-repair and backup recovery procedures after confirming drive health. A corrupted boot loader can stop startup even when firmware detects the physical disk.
Question 124
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: A new SATA drive is invisible in firmware because the technician used a defective data lead while power is present. A laptop with a replaced NVMe drive cannot find it because the new module uses an unsupported keying/protocol combination. What is the most appropriate plan for this situation?
- Restore the documented boot mode and correct boot entry before reinstalling the OS; install an SSD supported by the laptop M.2 connector and firmware.
- Replace or reseat the SATA data cable and verify the controller port; use approved startup-repair and backup recovery procedures after confirming drive health.
- Restore the documented boot mode and correct boot entry before reinstalling the OS; use approved startup-repair and backup recovery procedures after confirming drive health.
- Replace or reseat the SATA data cable and verify the controller port; install an SSD supported by the laptop M.2 connector and firmware.
Explanation
Correct Answer
D:For ticket (1), Powering a drive does not ensure the host has a functioning data channel. For ticket (2), Different M.2 modules may be physically or electrically incompatible despite similar packaging.
Incorrect Answers
A:For ticket 1, replace or reseat the SATA data cable and verify the controller port. Powering a drive does not ensure the host has a functioning data channel.
B:For ticket 2, install an SSD supported by the laptop M.2 connector and firmware. Different M.2 modules may be physically or electrically incompatible despite similar packaging.
C:For ticket 1, replace or reseat the SATA data cable and verify the controller port. Powering a drive does not ensure the host has a functioning data channel. For ticket 2, install an SSD supported by the laptop M.2 connector and firmware. Different M.2 modules may be physically or electrically incompatible despite similar packaging.
Question 125
A support team must resolve TWO distinct issues at the same location, using approved non-destructive maintenance: A workstation's boot disk appears in BIOS but the OS loader fails after an unexpected power loss. A laptop with a replaced NVMe drive cannot find it because the new module uses an unsupported keying/protocol combination. Which course of action addresses the stated issues?
- Restore the documented boot mode and correct boot entry before reinstalling the OS; replace or reseat the SATA data cable and verify the controller port.
- Use approved startup-repair and backup recovery procedures after confirming drive health; install an SSD supported by the laptop M.2 connector and firmware.
- Restore the documented boot mode and correct boot entry before reinstalling the OS; install an SSD supported by the laptop M.2 connector and firmware.
- Use approved startup-repair and backup recovery procedures after confirming drive health; replace or reseat the SATA data cable and verify the controller port.
Explanation
Correct Answer
B:For ticket (1), A corrupted boot loader can stop startup even when firmware detects the physical disk. For ticket (2), Different M.2 modules may be physically or electrically incompatible despite similar packaging.
Incorrect Answers
A:For ticket 1, use approved startup-repair and backup recovery procedures after confirming drive health. A corrupted boot loader can stop startup even when firmware detects the physical disk. For ticket 2, install an SSD supported by the laptop M.2 connector and firmware. Different M.2 modules may be physically or electrically incompatible despite similar packaging.
C:For ticket 1, use approved startup-repair and backup recovery procedures after confirming drive health. A corrupted boot loader can stop startup even when firmware detects the physical disk.
D:For ticket 2, install an SSD supported by the laptop M.2 connector and firmware. Different M.2 modules may be physically or electrically incompatible despite similar packaging.
Question 126
A service coordinator has THREE separate support tickets and needs the correct matching actions: A PC reports no bootable device after a technician changes the UEFI boot mode from the original configuration. A new SATA drive is invisible in firmware because the technician used a defective data lead while power is present. A workstation's boot disk appears in BIOS but the OS loader fails after an unexpected power loss. Which response best addresses these needs?
- Restore the documented boot mode and correct boot entry before reinstalling the OS; replace or reseat the SATA data cable and verify the controller port; and use approved startup-repair and backup recovery procedures after confirming drive health.
- Install an SSD supported by the laptop M.2 connector and firmware; replace or reseat the SATA data cable and verify the controller port; and use approved startup-repair and backup recovery procedures after confirming drive health.
- Restore the documented boot mode and correct boot entry before reinstalling the OS; install an SSD supported by the laptop M.2 connector and firmware; and use approved startup-repair and backup recovery procedures after confirming drive health.
- Restore the documented boot mode and correct boot entry before reinstalling the OS; replace or reseat the SATA data cable and verify the controller port; and install an SSD supported by the laptop M.2 connector and firmware.
Explanation
Correct Answer
A:For ticket (1), Firmware boot configuration must match the disk's installed boot environment. For ticket (2), Powering a drive does not ensure the host has a functioning data channel. For ticket (3), A corrupted boot loader can stop startup even when firmware detects the physical disk.
Incorrect Answers
B:For ticket 1, restore the documented boot mode and correct boot entry before reinstalling the OS. Firmware boot configuration must match the disk's installed boot environment.
C:For ticket 2, replace or reseat the SATA data cable and verify the controller port. Powering a drive does not ensure the host has a functioning data channel.
D:For ticket 3, use approved startup-repair and backup recovery procedures after confirming drive health. A corrupted boot loader can stop startup even when firmware detects the physical disk.
Question 127
A device support specialist must respond to this request: Two wireless headsets appear in a phone's Bluetooth scan but the target headset never enters discoverable pairing mode. Which next step MOST directly resolves the reported condition?
- Enable the supported NFC capability and verify application and device policy permissions.
- Put the intended headset into pairing mode and confirm its identity before entering the displayed PIN.
- Use NFC-capable hardware for the intended close-proximity interaction.
- Reposition the hub or receiver and check 2.4 GHz interference before replacing the mouse.
Explanation
Correct Answer
B:Nearby powered Bluetooth devices are not necessarily available for first-time pairing.
Incorrect Answers
A:Enabling the supported NFC capability and verifying application and device policy permissions would not put the intended headset into pairing mode and confirm its identity.
C:Using NFC-capable hardware for the intended close-proximity interaction would not put the intended headset into pairing mode and confirm its identity.
D:Reposition the hub or receiver and check 2.4 GHz interference would not put the intended headset into pairing mode and confirm its identity.
Question 128
An end user reports the following condition: A kiosk requires a tap-to-read badge at a few centimeters, but an engineer recommends a long-range Wi-Fi link instead. What should the support specialist recommend FIRST within the stated limits?
- Enable the supported NFC capability and verify application and device policy permissions.
- Put the intended headset into pairing mode and confirm its identity before entering the displayed PIN.
- Use NFC-capable hardware for the intended close-proximity interaction.
- Reposition the hub or receiver and check 2.4 GHz interference before replacing the mouse.
Explanation
Correct Answer
C:NFC is optimized for short-range contactless exchanges, unlike general networking radios.
Incorrect Answers
A:Availability of an NFC chip does not imply the operating system allows the requested feature; nFC is optimized for short-range contactless exchanges, unlike general networking radios.
B:Nearby powered Bluetooth devices are not necessarily available for first-time pairing; nFC is optimized for short-range contactless exchanges, unlike general networking radios.
D:High-speed USB electronics can create radio-frequency noise that affects nearby Bluetooth receivers; nFC is optimized for short-range contactless exchanges, unlike general networking radios.
Question 129
A help desk receives a support ticket with this evidence: A Bluetooth mouse works beside a laptop but intermittently disconnects when a USB 3 peripheral hub is placed between them. What is the MOST appropriate technician action?
- Use NFC-capable hardware for the intended close-proximity interaction.
- Reposition the hub or receiver and check 2.4 GHz interference before replacing the mouse.
- Enable the supported NFC capability and verify application and device policy permissions.
- Put the intended headset into pairing mode and confirm its identity before entering the displayed PIN.
Explanation
Correct Answer
B:High-speed USB electronics can create radio-frequency noise that affects nearby Bluetooth receivers.
Incorrect Answers
A:NFC is optimized for short-range contactless exchanges, unlike general networking radios; high-speed USB electronics can create radio-frequency noise that affects nearby Bluetooth receivers.
C:Availability of an NFC chip does not imply the operating system allows the requested feature; high-speed USB electronics can create radio-frequency noise that affects nearby Bluetooth receivers.
D:Nearby powered Bluetooth devices are not necessarily available for first-time pairing; high-speed USB electronics can create radio-frequency noise that affects nearby Bluetooth receivers.
Question 130
A field technician verifies the following customer equipment condition: A user has an NFC-enabled phone but contactless transaction features remain disabled in the handset's settings. Which response BEST addresses the actual cause or requirement?
- Enable the supported NFC capability and verify application and device policy permissions.
- Put the intended headset into pairing mode and confirm its identity before entering the displayed PIN.
- Use NFC-capable hardware for the intended close-proximity interaction.
- Reposition the hub or receiver and check 2.4 GHz interference before replacing the mouse.
Explanation
Correct Answer
A:Availability of an NFC chip does not imply the operating system allows the requested feature.
Incorrect Answers
B:Putting the intended headset into pairing mode and confirming its identity would not enable the supported NFC capability and verify application and device policy permissions.
C:Using NFC-capable hardware for the intended close-proximity interaction would not enable the supported NFC capability and verify application and device policy permissions.
D:Reposition the hub or receiver and check 2.4 GHz interference would not enable the supported NFC capability and verify application and device policy permissions.
CompTIA A+ Certification Exam: Core 1 (220-1201) Practice Tests